亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pushing cylinder Sold to Ecuador

Release time:2023-12-08 14:41:25 Hits: Current position: Home > News

This article mainly introduces:

Ecuador hydraulic cylinder,pushing cylinder manufacturer,pushing cylinder

Ecuador pushing cylinder

(Ecuador pushing cylinder,produced by Hengyu Hydraulic Cylinder Factory)

pushing cylinder are widely used in Ecuador,because of no need for deceleration device,long service life,smooth movement.So our company has designed pushing cylinder for customers from Ecuador.

Introduction to pushing cylinder:

When the pushing cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the pushing cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

pushing cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The assembly work of the pushing cylinder has a great impact on the quality of the pushing cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Most of the failure of the pushing cylinder is because there is a foreign body in the pushing cylinder into the failure of the pushing cylinder, the most problematic is that it is difficult to determine when the foreign body is into the pushing cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about pushing cylinder:

What hydraulic valve is used to control a cylinder back and forth?
Direction valve is available. Direction valve includes electromagnetic directional valve, manual directional valve, check valve, hydraulic control check valve, the specific choice of which direction valve, you need to see the use of conditions.

When the superimposed hydraulic control valve is added to the bottom of a solenoid valve and a double directional throttle valve, why does the cylinder shock on the return trip?
The stack hydraulic control check valve must be added above the stack one-way throttle valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美操视频| 国产丰满啪啪自拍| 人妻制服诱惑中文| 国产XXXXXXXX| AV在线男人的天堂观看网站| 春桃久久久久| 欧美在线艹美女视频| 日本一区二区成人网站| 日本成人免费不卡| 欧美日精品b小视频网站播放| 好舒服啊啊啊啊啊视频| 午夜福利在线大香蕉| 阿拉善右旗| 男人去天堂AV| 月色导航网站免费| 制服丝袜自拍偷拍| 日本熟妇五十路在线视频| 国产二区三区大长脚| 中文字幕日色| 自拍视频区在线| 四区五区视频在线观看| 啊啊啊啊啊啊啊好爽啊啊啊啊啊啊啊日韩| 美女1区2| 日本不卡一二大香蕉| 久久尤物一区二区三区| 深夜激情网在线观看| 成人AV一区二区三区四区五区| 亚洲中文在线有码| 啊啊干我舔我好舒服视频插我操我| av北条麻妃在线| 亚洲日韩性爱电影网站| 逼视频日韩| 嗯啊嗯啊快点痒视频| 国产 日韩 欧美性经典| 人人爱小黄片| 国产精品午夜福利视频| 91男操美女| 日韩不卡区高清在线视频| 91又粗又硬| 国产 传媒 精品 页 区 日| 中文墓区二区三区四区视频|