亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steel mill cylinder Sold to Czech Republic

Release time:2023-12-02 14:47:32 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

Czech Republic steel mill cylinder

(Czech Republic steel mill cylinder,produced by Hebei Hengyu company)

steel mill cylinder are widely used in Czech Republic,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed steel mill cylinder for customers from Czech Republic.

Introduction to steel mill cylinder:

The viscosity of the working oil used in the steel mill cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

The internal leakage of the steel mill cylinder should be prevented when the steel mill cylinder is used. The internal leakage of steel mill cylinder includes the leakage caused by excessive wear of steel mill cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The piston rod and guide sleeve function of the steel mill cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

What kind of process is used in the steel mill cylinder to make high-quality steel mill cylinder products: the body is the main component of the steel mill cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The steel mill cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the steel mill cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the steel mill cylinder increases by 25%. If the service life of the steel mill cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. steel mill cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the steel mill cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and steel mill cylinder are stuck or the steel mill cylinder is blocked. At this time, no matter how to manipulate, the steel mill cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steel mill cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about steel mill cylinder:

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.

When does the cylinder rotate?
The piston rod inside the multistage plunger cylinder can be rotated, and it will rotate when it is subjected to tangential force.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩人妻激情| 粉嫩白虎被操| 美女福利电影在线观看亚洲一区二区| 精品一区二区三区四区五区在线观看| 无码六十六区| 91av大神| 日本有码 在线观看| 后入骚妇大屁股| 女人被男人日得很爽视频网站免费看 | 一本道成人资源站| 亚洲美女的激情啪啪啪| 国内插插视频| 骚女人操毴| 舔一舔AV高清| 人妻人人做人碰人人爽91| 午夜视频成年| 中午字幕日韩1区2区懂色| 一级美女黄色操逼视频| 日韩老妓女| 插一区二区| 午夜福利视频 一区| 欧美女郎久久五月| 国产传媒在线观看入口| 摸逼视频日本| 嗯啊好刺激操我大奶子视频| 欧美日韩国产高清在线不卡| 天天操天天添| 国产五月丁香六月| 91人妻偷拍| 女V中文字幕操你| 亚洲vs日本vs欧洲免费一区| 欧美兽交在线| 日韩 综合 另类专区| 成人午夜av在线播放| 美女XX内射熟女| 偷拍偷拍精品| 亚洲插进去| 天操天天干蜜臀| 天堂AV在线一位| 欧美视频精选| 看操小逼逼|