亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Egypt

Release time:2023-12-02 14:47:29 Hits: Current position: Home > News

This article mainly introduces:

Egypt hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Egypt shearing machine cylinder

(Egypt shearing machine cylinder,produced by Hengyu Hydraulic Co., Ltd)

shearing machine cylinder are widely used in Egypt,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed shearing machine cylinder for customers from Egypt.

Introduction to shearing machine cylinder:

When the initial action of the shearing machine cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the shearing machine cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

The viscosity of the working oil used in the shearing machine cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

If the seal of the shearing machine cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

The main role of the shearing machine cylinder: the shearing machine cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the shearing machine cylinder realizes reciprocating motion. The structure of the shearing machine cylinder has three categories: piston shearing machine cylinder, plunger shearing machine cylinder, swing shearing machine cylinder, piston shearing machine cylinder and plunger shearing machine cylinder to achieve reciprocating linear motion, output speed and thrust, swing shearing machine cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the shearing machine cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The shearing machine cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

Answers to some questions about shearing machine cylinder:

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
呀呀呀啊啊啊操操操| 艹艹大大精品黑人欧美| 大黑屌插少妇| 扒开美女的逼用力捅| 大鸡巴黑鬼操人妻| 国产成人AV一区在线观看| 亚洲无码动作| 18p亚洲91| 中国美女黄色片| 久久美女一二区| 青青草香蕉91| 婷婷丁香91综合| 无码黑丝制服在线| 欧美两人左线视频网站 | 性感日韩美女操逼| 啊啊啊操操操啊啊| 亚洲精品Ⅴ欧洲精品| 日本韩国国产黄色小视频网站| 毛片一区二区三区四区五区六区| 国广黄片高清| 大黑鸡巴日少妇| 美女草逼视频网站| 一级做a暖暖在线观看| 日韩谢精| 男女做爱免费观看网站| 湿了好想要视频| 香蕉日韩| 成人操美女| 2424.com大香蕉| 91xxx女操有限公司| 熟女亂伦一区二区| 日韩久久久久综 合| 麻豆视频大尺度| 欧美一区激情文学| 亚洲av天天舔| 黑人大机巴操肥逼视频| 无码人妻aⅴ一区二区三区麻豆| 91大神福利视频网| 国产夫妻偷拍白拍| 国产日韩欧美亚一级视频| 亚洲天天狠狠干AV|