亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pressure plate hydraulic cylinder Sold to Slovenia

Release time:2023-11-30 11:00:06 Hits: Current position: Home > News

This article mainly introduces:

Slovenia hydraulic cylinder,pressure plate hydraulic cylinder manufacturer,pressure plate hydraulic cylinder

Slovenia pressure plate hydraulic cylinder

(Slovenia pressure plate hydraulic cylinder,produced by Hebei Hengyu company)

pressure plate hydraulic cylinder are widely used in Slovenia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed pressure plate hydraulic cylinder for customers from Slovenia.

Introduction to pressure plate hydraulic cylinder:

If the pressure plate hydraulic cylinder slips or crawls, please check whether there is astringency inside the pressure plate hydraulic cylinder, because the internal parts of the pressure plate hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the pressure plate hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the pressure plate hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

When the pressure plate hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

When producing oil pressure plate hydraulic cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the pressure plate hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about pressure plate hydraulic cylinder:

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲成人精品不卡中文字幕| 一级一级黄片| 成人av吃瓜在线播放| 乱一区二区| 国产内射在线传媒| 美女主播福利热舞视频在线观看网站| 白丝被爆操视频播放在线观看的人| 逼逼XXXX无码| 操大波美女视频欧美| 91XXX精品一区二区| 国产三级办公室| 中文字幕第一页,一区九区| 18禁美女。网站| 成人在线视频人妻3P| 亚日韩综合一区| 亚洲欧美色色色| 国产真实乱人偷视频在线观看 | 另类福利激情视频| 亚洲国产九九热| 大鸡巴作爱视频| 香蕉狠狠在线视频| 玩大鸡巴视频| 日本不卞视频| 浙江少妇自慰| 小骚货免费视频网站| 啊啊啊啊啊啊好大好爽免费视频| 国产骚视频| 超碰最新地址欧美| 狠狠做五| 尤物视频在线观看免费精品一区| 日本骚妇操屄| 亚洲一二三四五av| 超碰国语在线不用播| 欧洲在线一区二区熟女| 日本精品手机在线视频| 日韩成人性网| 日韩精品亚洲一区| 久久五月婷婷色播| 日本老熟乱一区二区| 成人五月婷在线观看色色激情网| 鸡巴操我逼|