亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

cargo elevator hydraulic cylinder Sold to Jordan

Release time:2023-11-30 11:00:05 Hits: Current position: Home > News

This article mainly introduces:

Jordan hydraulic cylinder,cargo elevator hydraulic cylinder manufacturer,cargo elevator hydraulic cylinder

Jordan cargo elevator hydraulic cylinder

(Jordan cargo elevator hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

cargo elevator hydraulic cylinder are widely used in Jordan,because of long service life,smooth movement,high work efficiency.So our company has designed cargo elevator hydraulic cylinder for customers from Jordan.

Introduction to cargo elevator hydraulic cylinder:

Protection of the cargo elevator hydraulic cylinder surface: During the dismantling process, safety protection should be carried out on the cargo elevator hydraulic cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the cargo elevator hydraulic cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the cargo elevator hydraulic cylinder should be cleaned up in time.

Improve the service life of the cargo elevator hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the cargo elevator hydraulic cylinder (such as the cargo elevator hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the cargo elevator hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the cargo elevator hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single cargo elevator hydraulic cylinder exhaust.

The "O" ring can be used as an auxiliary seal inside the cargo elevator hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the cargo elevator hydraulic cylinder, and can be completely sealed.

The material of the sliding part of the cargo elevator hydraulic cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

Answers to some questions about cargo elevator hydraulic cylinder:

How to calculate the tonnage of the hydraulic press without konowing the diameter of the cylinder?
To know the tonnage of the hydraulic cylinder, you first need to know the working pressure of the hydraulic system, the inner diameter of the hydraulic cylinder and the outer diameter of the cylinder rod (the outer diameter of the cylinder rod is needed when calculating the hydraulic cylinder tension). The thrust of the hydraulic cylinder (that is, the force that the hydraulic cylinder can produce by extending out) = the cross-sectional area of the hydraulic cylinder (or the cross-sectional area of the piston) × the working pressure of the cylinder (the cross-sectional area of the piston) =pi*D^2/4= PI (take 3.14) × the square of the cross-sectional area of the piston ÷4 working pressure to see the pressure displayed on the pressure gauge when the maximum load is working.

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩爱爱视频网站| 五月天堂激情| 黄色电影在线观看制服丝袜美腿丝袜| 日韩精品一区二区伦理片| 日本欧洲不卡区| 亚洲激情不卡视频| 女主播被操在线播放| 国产熟妇色在线观看一下| 人妻有码中文字幕AK| 国产黄色3a大片在线观看| 128福利视频| 2024日韩欧美人妻精品| 精品视频 精品素人| 青青操免费视频专区| 亚洲无码丝袜人妻精一区二区三区| 国产偷拍日韩无码欧美视频| 涩五月网| www.xxx日本一区二区| 亚洲欧美综合国产精品| 国产精品999下线| 日韩一级二级三级| 成人在线视频导航| 大鸡巴操了在线观看| 日本亚洲有码在线播放| 我想日外国美女小逼视频看看| 久久丝袜亚洲| 色女优天堂| 国产伦一区二区三区高潮| 青青热免费视频在线观看| 亚洲尤物一区二区| 大鸡巴插小穴在线看| 中出内射在线四区| 精品一曲二曲三区在线观看| 国产破处视频在线看| 国外性感美女操逼视频| 性欧美大香蕉| 91超a大片| 色天堂丁香| 大胸av| 騷逼1區| 共和县|