亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pushing cylinder Sold to Slovakia

Release time:2023-11-30 11:00:02 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,pushing cylinder manufacturer,pushing cylinder

Slovakia pushing cylinder

(Slovakia pushing cylinder,produced by Hengyu Group)

pushing cylinder are widely used in Slovakia,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed pushing cylinder for customers from Slovakia.

Introduction to pushing cylinder:

The piston rod of the pushing cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

If the seal of the pushing cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Before purchasing the pushing cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

When the control pressure of the hydraulic system is too low, the pushing cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about pushing cylinder:

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

How to refuel pneumatic riveting cylinder?
First put the gun flat, that is, horizontally, while pushing the stroke positioning pin and loosen the back cover, rotate to the left for a maximum of five turns, and then use a wrench to loosen the oil sealing screw, slowly add the hydraulic oil and let the air out, fill up to tighten the oil sealing screw. This process of adding hydraulic oil is over.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品国产精偷| 欧美好好操逼| 啊啊啊啊不要啊…啊…嗯嗯视频| 美女裸交无遮挡免费视频网站| 国内鸡巴调教骚逼| 国产青青草麻豆| 亚洲欧美×××××| 午夜福利入口三| 欧美日韩骚逼熟女| 水啪啪视频| AV在线精品一区二区| 国产喷水欧美| 92自拍美女视频| 亚洲最大成人在线观看| 国产成人自拍偷拍在线| 初撮五十路人妻中出在线| 嗯嗯嗯嗯嗯好爽视频| 嗯嗯嗯嗯嗯嗯嗯啊啊啊啊啊在线| 欧美日韩一级视频看看| 精品人妻伦九区久久AAA片| 操到喷水免费看| 久久美熟女| 青草一区| 被大鸡巴操好爽视频| 亚洲熟女乱一区| 国产日本亚洲香蕉| 熟女人五十路| 美女永久免费视频| 松滋市| 中文字幕欧美极品| 操B视频欢看| 黑人巨屌连续中出人妻| 无码肛交一区在线观看| 亚州精品av一区二区| 欧洲美女搞鸡巴免费观看| 日韩精品黄色| 亚洲无码 制服诱惑 中文字幕| 欧美区亚洲区 日韩区小说区 | 欧美老女人谣乱视频| 超碰最新中文字幕不卡| 日本国产一区二区淫荡|