亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push bench hydraulic cylinder Sold to Mexico

Release time:2023-11-28 10:55:45 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,push bench hydraulic cylinder manufacturer,push bench hydraulic cylinder

Mexico push bench hydraulic cylinder

(Mexico push bench hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

push bench hydraulic cylinder are widely used in Mexico,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed push bench hydraulic cylinder for customers from Mexico.

Introduction to push bench hydraulic cylinder:

If the push bench hydraulic cylinder slips or crawls, please check whether there is astringency inside the push bench hydraulic cylinder, because the internal parts of the push bench hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the push bench hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the push bench hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

When the initial action of the push bench hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the push bench hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Factors that should be considered when selecting the oil seal in the push bench hydraulic cylinder: some specific factors should be taken into account when selecting the oil seal in the push bench hydraulic cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: push bench hydraulic cylinder diameter, piston rod diameter, piston rod and piston groove size, push bench hydraulic cylinder working pressure, push bench hydraulic cylinder movement speed, hydraulic system oil temperature and push bench hydraulic cylinder working environment.

When the push bench hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the push bench hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about push bench hydraulic cylinder:

What is the smallest cylinder size?
The smallest shape cylinder I have ever seen is a hydraulic clamping cylinder in the machine tool industry. Outer diameter 24 mm, total length 23 mm, travel 4 mm. Weighs 0.05 kg. Maximum clamping force 3500 Newtons.

What valve is used to control cylinder expansion?
Mainly use reversing valve, but the details of the control need hydraulic control valve, hydraulic control valve can be divided into direction control valve, pressure control valve, flow control valve. The valve controls the expansion of the cylinder is the direction control valve, that is, the reversing valve. What is the meaning of two-position three-way and three-position four-way of the reversing valve? Usually according to the different working positions that can stay after the spool is moved, it can be divided into: two-position valves, three-position valves and multi-position valves. According to the number of different slide valve channels can be divided into: two-way valve, three-way valve, four-way valve, five-way valve and multi-way valve. The name of the reversing valve is called the multi-position and multi-pass reversing valve according to its working position and the number of channels.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
五月六月亭亭性爱视频| 欧美亚洲日韩成人黄片在线| 大量白虎被强操视频入口处| 一区二区狠狠.操精品| 操小屄毛片| 91操到喷水| 国产西区二区在线| 亚洲日韩国产欧美老熟女| 好大好骚好爽好深好黄视频在线| 激情五月宗和网| 日本熟妇色一区| 国产日韩欧美成人精品| 色婷婷区二区三区妖精视频| 桓仁| 嗯啊好舒服我要视频| 色呦呦国产一区二区精品无码| 日韩黄色美女视频| 大鸡吧抽插小嫩逼的视频| 东北美女操大逼| 亚洲精品丝袜操逼| 中文字幕精品一区在线播放| 熟妇人妻精品| 中文字幕执行1区2区| 性生活试看视频久久久久久中文字幕亚洲| 国产国语黄色片| 五月婷婷美女自卫| 大鸡吧操逼国产| 日韩一本道超碰在线| 射美女91| 熟女一区二区中文字| 中字人妻伦欲中文字幕| 激情综合TTs| 亚洲视频一二三区在线| 人妻精品少妇精品| 骚逼被大鸡巴操到高潮视频| 极品的亚洲操逼| 逼几巴| 五月婷婷丁香传媒| 日逼视频啊啊啊高潮了视频| 嗯嗯嗯嗯嗯日本视频| 一本一道AV影音|