亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pusher hydraulic cylinder Sold to Uruguay

Release time:2023-11-28 10:55:23 Hits: Current position: Home > News

This article mainly introduces:

Uruguay hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

Uruguay pusher hydraulic cylinder

(Uruguay pusher hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

pusher hydraulic cylinder are widely used in Uruguay,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed pusher hydraulic cylinder for customers from Uruguay.

Introduction to pusher hydraulic cylinder:

pusher hydraulic cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

The repair method of the pusher hydraulic cylinder: the repair of the pusher hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The assembly work of the pusher hydraulic cylinder has a great impact on the quality of the pusher hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the control pressure of the hydraulic system is too low, the pusher hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about pusher hydraulic cylinder:

About the hydraulic cylinder wall thickness problem?
Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91国精品产品一区二区三区闺蜜| 操鸡视频网站免费观看| 欧美一级 片日韩精品| 91美女插出白浆| 美女鸡吧在线观看| 日本肏穴一二三| 超级97超碰| 91热碰| 日女人逼AV| A片一区二区在线观看| 超碰九七精品在线观看| 动漫操骚逼视频电影| 超碰在线最新| 都兰县| 大香蕉丰满人妻| 青青草原男人天堂网| 12345亚洲经典| 超碰97免费人妻麻豆| 国产高潮高潮久久久| 超在线97大香蕉| 波多野结衣一区二区| 四品无码在线| 91无码人妻精品一区二区三区蜜桃| 国产精品97超碰大香蕉| 成人激情草草草视频| 午夜寂寞福利手机影院小视频| 啊啊啊啊很舒服在线观看| 日韩黄片大香蕉| 美女爱日逼免费视频| 亚洲女同性一区二区三区| 免费无遮挡99视频| 黑人大吊日女人视频| 性爱区综合网| 我要看大鸡巴操小逼视频| 嗯嗯嗯嗯在线观看| 日本东方操逼视频| 中文字幕区在线| 日韩成人做暧暧视频在线观看 | 熟妇大屁屁一区二区三区| 在线看喷插骚穴骚穴| 玖玖综合色五月|