亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic lift cylinder Sold to Uruguay

Release time:2023-11-28 10:55:18 Hits: Current position: Home > News

This article mainly introduces:

Uruguay hydraulic cylinder,hydraulic lift cylinder manufacturer,hydraulic lift cylinder

Uruguay hydraulic lift cylinder

(Uruguay hydraulic lift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

hydraulic lift cylinder are widely used in Uruguay,because of long service life,smooth movement,high work efficiency.So our company has designed hydraulic lift cylinder for customers from Uruguay.

Introduction to hydraulic lift cylinder:

hydraulic lift cylinders in series, parallel and series parallel. Series: In the hydraulic lift cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the hydraulic lift cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the hydraulic lift cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the hydraulic lift cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

If air enters the hydraulic system, the hydraulic lift cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

In recent years, the processing process of the hydraulic lift cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

The hydraulic lift cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the hydraulic lift cylinder should pay attention to: the operation should be as far away from the hydraulic lift cylinder as possible, to avoid falling objects, knocking, rubbing the hydraulic lift cylinder coating. When cleaning the hydraulic lift cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the hydraulic lift cylinder when the oil temperature exceeds 70 ° C.

Answers to some questions about hydraulic lift cylinder:

How to deal with oil cylinder leakage?
The causes of oil leakage and treatment methods are as follows: (1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear. (2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.

How to calculate the hydraulic cylinder pressure, how much pressure can put up how much weight?
There is a formula for air pressure, hydraulic pressure, water pressure: F=P×S type: f-cylinder or hydraulic cylinder output, unit is Newton (N) P- pressure, unit is Mpa S- effective area, unit is square millimeter (mm2), note: is the effective area, in the hydraulic cylinder to subtract the cross-sectional area of the piston rod.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91黄色视屏| 精品日b2| 国产18线在线精品| 噜噜噜Av蜜桃| 美女插粉逼| 操女生在线| 韩日老女人性视频| 国产对白AV一区二区| 嗯嗯嗯嗯嗯嗯嗯啊啊啊在线观看| 考逼视频黄片| 中文字幕怎样操逼| 日本操逼视频论坛| 欧美大鸡巴人妻| 熟妇一区二区三区四区蜜桃| 亚洲激情 偷拍自拍 主播| 人妻 有码 中文| 日韩欧美俄成人| 中文字幕com.超碰| 性色av.一区二区| 东京热AV无码| 一区二区三区三州高清| 甘孜县| 国产酒店呻吟对白| 啊嗯操的我好爽视频| 53岁亚洲熟妇在线| 让你看骚逼逼AV| 日本人妻熟女五十路一区二区三区四区| 色婷婷丁香,开心六月| 啊嗯啊好爽好舒服啊视频在线观看 | 大色网小色网淫色网在线观看| 亚洲国产日韩御姐| 久热333| 亚洲自拍色色色网| 精品老肥熟女视频一区二区三区| 色五月亭综合| 欧美日韩免费成人一级片| 极品少妇1区2区| 大鸡吧插小穴视频重口| 超碰丝袜人妻在线| 插逼逼手机观看| 国产肏我视频|