亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Poland

Release time:2023-11-28 10:55:15 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Poland swager cylinder

(Poland swager cylinder,produced by Hengyu Group)

swager cylinder are widely used in Poland,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed swager cylinder for customers from Poland.

Introduction to swager cylinder:

Do not enter foreign bodies when installing the swager cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

When the hydraulic oil is not pumped into the swager cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the swager cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

In order to ensure the service life of the swager cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

swager cylinder installation precautions: Before installing the swager cylinder into the system, the parameters on the swager cylinder label should be compared with the parameters when ordering. The base of the swager cylinder must have sufficient stiffness, otherwise the swager cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Answers to some questions about swager cylinder:

What is the meaning of cylinder HSGK01-100/70E-4111-1320?
hsg Double acting single piston rod hydraulic cylinder and front end cover are connected by internal clamp key 01 Design serial number 100 cylinder inner diameter 70 piston rod outer diameter e Pressure class code 16mpa4111 Front flange, rod end external thread, both ends with buffer, oil port connection is internal thread 1320 stroke.

Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
东京热91麻豆| 欧美日韩国产人妻一区二区三区| 日韩性爱大片网站| 免费看中国美女操B视频| 婷婷操香蕉| 高清无码九区| 大鸡巴操大鸡巴舔大鸡巴日大鸡巴吃| 肉感尻在线| 又粗又长日本视频| 久久久一区二区精品人体艺术| 淫浪操逼视频看看| 欧美性爱日韩电影国产高清 | 精品亚洲一区二区三区奶水| 曹小琴小骚屁穴中文字幕一区二区视频 | 中日韩欧美精品一级| 国产人体区二区| 欧美 日韩 国产一二| 啊啊啊啊干AV| 婷婷五月国产馆在线| 3A黄片女同视频免费看| 制服丝袜诱惑经典在线| 欧洲少妇视频| 日本嗯嗯啊啊中文字幕| 中文字幕免AV风间| 九一黄色三级操逼视频在线播放| 日韩成人网站免费观看| 抽插抽插小穴| 五月婷婷美国| 欧美日小穴| 夜夜干欧美干欧美干| 波多野结衣操大奶| 抽动小穴视频| 超碰97在线免费公开| 国产一二三视频网址| 日韩伦理电影一区二区| 国产熟女自拍合集| 91宅男免费在线观看| 91精品蜜臀| 兄妹无码一区| 国产大鸡巴操小逼| 午夜成人福利人妻AV|