亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Malaysia

Release time:2023-11-26 09:50:20 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Malaysia reciprocating cylinder

(Malaysia reciprocating cylinder,produced by Hebei Hengyu company)

reciprocating cylinder are widely used in Malaysia,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed reciprocating cylinder for customers from Malaysia.

Introduction to reciprocating cylinder:

After chrome plating of the piston rod of the reciprocating cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

There are some honeycomb holes in the inner wall of the reciprocating cylinder, piston or piston rod surface. How is this formed? When we repair the reciprocating cylinder, we can see that there are some honeycomb holes on the inner wall of the reciprocating cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the reciprocating cylinder is targeted to prevent. Is very necessary.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the reciprocating cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

In the process of using the reciprocating cylinder, sometimes such a problem will occur, the reciprocating cylinder can not act immediately after the instruction of the reciprocating cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil reciprocating cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about reciprocating cylinder:

How to distinguish cylinder rod head and cylinder bottom?
One end of the piston rod can be telescopic is the rod head, and the one behind is the bottom of the cylinder, which is the single rod cylinder.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
人妻熟女丝袜视频| 综合网熟女就去干| 中文字幕视频一区在线观看第3页| 无码人妻aⅴ一区二区三区麻豆| 91色天天| 超碰97人妻免费在线| 日韩高清一区在线观看| 掰开小穴大鸡巴插进去视频| 亚洲欧美另类激情综合区粉芽| 啊不要操我久久精品| 尿尿av一区二区| 不卡的黄色网| 高清无吗一二三在线观看在线观看视频| 啊啊啊啊插进来吧网站视频在线观看| 国产AA欧美曰韩激情影片| 大黑比网站| 男人用大鸡巴操美女| 啊啊啊啊啊啊 受不了了 爆操视频 | 亚洲国产另类久久精品| 大鸡巴日小逼逼视频日日日| 日本韩国香蕉成人视频| 淫趴趴导航| 中文字幕男同性恋久久久精品| 大黑屌草白逼| 自拍偷拍亚洲图| 女同舌吻成人视频18禁| 久久福利二区| 大屁股美女呻吟声| 看操大骚逼| 日韩无码Ab| 一七六九成人在线视频| 山东省| 日韩少妇mf视频在线观看| 亚洲欧美日韩国产另类毛片| 欧美中文字幕在线观看一区二区三区| 干B视频在线观看| 精品一区二区在线观看| 1福利在线| 日韩老司机深夜视频| 九色无码| 骚逼四区|