亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to Paraguay

Release time:2023-11-26 09:49:49 Hits: Current position: Home > News

This article mainly introduces:

Paraguay hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

Paraguay stroke adjustable cylinder

(Paraguay stroke adjustable cylinder,produced by Hebei Hengyu company)

stroke adjustable cylinder are widely used in Paraguay,because of excellent temperature resistance,powerful torque,no need for deceleration device.So our company has designed stroke adjustable cylinder for customers from Paraguay.

Introduction to stroke adjustable cylinder:

When the stroke adjustable cylinder needs to be stored for a period of time, please follow the recommended methods: The stroke adjustable cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the stroke adjustable cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil stroke adjustable cylinder should not be in direct contact with water vapor for a long time. The stroke adjustable cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the stroke adjustable cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the stroke adjustable cylinder Before working, the stroke adjustable cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the stroke adjustable cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

There are some honeycomb holes in the inner wall of the stroke adjustable cylinder, piston or piston rod surface. How is this formed? When we repair the stroke adjustable cylinder, we can see that there are some honeycomb holes on the inner wall of the stroke adjustable cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the stroke adjustable cylinder is targeted to prevent. Is very necessary.

When the stroke adjustable cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the stroke adjustable cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the stroke adjustable cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the stroke adjustable cylinder can meet the requirements by grinding. However, the life and reliability of this repair stroke adjustable cylinder are not high.

If the stroke adjustable cylinder slips or crawls, please check whether there is astringency inside the stroke adjustable cylinder, because the internal parts of the stroke adjustable cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the stroke adjustable cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the stroke adjustable cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about stroke adjustable cylinder:

Why can't the hydraulic cylinder be replaced with water?
Hydraulic oil for hydraulic transmission has a variety of requirements for viscosity, density, flow rate, and temperature, which are not available for water.

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本老司机成人影视| 中文字幕北岛玲日本| 熟女真一区二区三区SXXHD| 三级片中文字母免费观看| 成人午夜一区二区三区在线| 久亚洲精品| 昌都县| 欧美美女野外操逼视频| 鸡巴视频在线观看www| 日本熟妇五十路六十路在线视频| 青青综合色| 兴安县| 女同性恋成人午夜亚洲一区| 色色五月亚洲| 丝袜制服自拍| 亚洲av男人电影天堂| 鸡巴插进逼里免费视频| 婷亚洲中文| 制服丝袜国产美女91| 96精品久久久久久| 夫妻大香蕉| 亚洲操操操| 操逼欧美网站| 免费看丝袜美女被操到高潮| 啊…操美女婢视频| 日本香蕉尤物视频| 三级毛片网站| 亚洲女AV在线播放一区二区三区| 青草自拍av| 嗯嗯啊啊上床国产视频| 极品美女探花| 天堂久久天堂色综合色| 蜜桃 aV午夜福利一区二区二区| 背德第一区希崎中文字幕| 极品美女被各种姿势 爆操的视频| 不要操了,疼视频| 福利大香蕉视频在线观看| 丝袜视频污污| 伦理电影网站国产一区二区伦理网站 | 国产成人av 免费| 国产视频第一区|