亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Costa Rica

Release time:2023-11-24 16:13:26 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Costa Rica stacker cylinder

(Costa Rica stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Costa Rica,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stacker cylinder for customers from Costa Rica.

Introduction to stacker cylinder:

The commonly used buffer structure of the stacker cylinder is composed of a piston boss and a stacker cylinder head groove. When the piston moves close to the stacker cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

There are some honeycomb holes in the inner wall of the stacker cylinder, piston or piston rod surface. How is this formed? When we repair the stacker cylinder, we can see that there are some honeycomb holes on the inner wall of the stacker cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the stacker cylinder is targeted to prevent. Is very necessary.

stacker cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the stacker cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the stacker cylinder. c. The stacker cylinder seal is extruded, if the O-ring is obviously extruded at the stacker cylinder seal, replace the stacker cylinder seal.

stacker cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about stacker cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

How to judge the failure of forklift hydraulic cylinder?
The common faults of the hydraulic cylinder of forklift truck are mainly crawling, insufficient thrust, working speed decline or even stop. Generally, crawling occurs at low speed. The main reason is that the air stored in the cylinder is not cleared. In addition, excessive or uneven mechanical friction can also cause crawling. Such as the piston and the piston rod different heart, the piston rod full length or local bending, the cylinder hole straightness is poor, the cylinder is drum shaped or has a large taper, the cylinder thin finish decline or produce hair, the cylinder installation accuracy is out of whack, the piston rod nuts at both ends of the screw too tight to make its concentricity is poor, the oil seal screw too tight friction is too large, will cause crawling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美一区二区高潮视频在线观看| 主播被操视频| 久久久之热| 老司机精品视频无码一区二区| 18+网站一区| 导航av大全| 自拍第五区| 蜜臀va亚洲va欧美va天堂| 少妇吞吐大黑屌| 黑人大战日本美女3级片| 中文字幕加勒比一区二区不卡| 国产传媒欧美日韩成人大片| 欧美美女爱大屌| 黄色网络中文字幕日本| 被大鸡巴插视频| 琪琪精品视频二区| 欧美熟妇视频一区二区三区| 在线观看嗯嗯嗯啊| 欧美麻豆一卡资源在线观看| 红桃AV午夜伦理在线| 免费福利在线视频| 抽插高潮白浆视频| 日本人妻乱又伦| 成人福利院| yy6050漫画| 不卡人妻少妇精品特级毛片一区二三区 | 天天综合亚洲色| 麻豆传媒 丝袜美腿| 五十路毛茸茸中文字幕| 亚州AV 国产| 日本人日b的视频| 大奶子插逼视频啊啊啊啊啊| 亚洲情侣激情在线| 成人骚逼艹逼内射视频| 农村粗腿熟妇呻吟声456| 我不卡影院特片网一卡二卡三卡 | 公开超碰97| 国产又粗又猛又爽又黄又高潮的视频| avav美女一区| 爱爱亚洲欧美| 媚药 在线|