亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Nigeria

Release time:2023-11-08 10:36:23 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Nigeria stern plate hydraulic cylinder

(Nigeria stern plate hydraulic cylinder,produced by Hebei Hengyu company)

stern plate hydraulic cylinder are widely used in Nigeria,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from Nigeria.

Introduction to stern plate hydraulic cylinder:

If air enters the hydraulic system, the stern plate hydraulic cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

If the stern plate hydraulic cylinder slips or crawls, please check whether there is astringency inside the stern plate hydraulic cylinder, because the internal parts of the stern plate hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the stern plate hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the stern plate hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

The material, shape and compression of the stern plate hydraulic cylinder seal have a great impact on the service life and work efficiency of the stern plate hydraulic cylinder. In addition to requiring a reliable seal, it should also have a long service life and less friction loss. At present, there are many seal manufacturers in the country, and it is also crucial to choose high-quality seals with reliable and stable quality.

The wear of the hard chromium plating layer of the stern plate hydraulic cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about stern plate hydraulic cylinder:

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产1区二区| 少妇缝18p二区| 日韩阴毛成人视频| 日本麻豆不卡| 91欧美激情一区二区| 中文字幕一区二区三区四区五区六区日本| 操美欧韩日屄| 国产伦精品一区二区三区人妻| 大鸡巴操大骚逼AV电影淫| 制服丝袜人妻中文字幕| 成人熟女人区一三区| 大鸡巴插小穴啊啊啊视频| 日韩大香蕉导航| 美女插鸡巴黄色免费| 狠一区二区三区熟女| 自排偷排视频一区欧美| 日本成人久久久久久| 美国美女性爱视屏| 老女人一二三四区| 国产搞嫩逼视频| 裸体重在线观看麻豆| 中文一区二区三区高清| 大香蕉官网手机视频在线| 欧美区一视频| 床戏视频插进去青青草| 欧美大鸡巴 一区二区三区 另类 吃瓜| av男人的午夜做爱天堂| 最近中文字幕1区2区| 国产黄色三级AV| 韩国一区av| 丰满美女超碰电影| 欧美日韩啊红桃视频| 大鸡吧日逼网站| 捅美女逼的视频| 美女快乐网站在线| 亚洲有码区妻| 日韩欧美亚洲一区在线观看| 一級毛片視頻| 大吊操大逼外国中国| 色悠悠午夜| 亚洲精品女人久|