亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Latvia

Release time:2023-11-24 16:13:24 Hits: Current position: Home > News

This article mainly introduces:

Latvia hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Latvia servo hydraulic cylinder

(Latvia servo hydraulic cylinder,produced by Hebei Hengyu company)

servo hydraulic cylinder are widely used in Latvia,because of smooth movement,no need for deceleration device,long service life.So our company has designed servo hydraulic cylinder for customers from Latvia.

Introduction to servo hydraulic cylinder:

How to determine the working pressure of the servo hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, servo hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Piston servo hydraulic cylinder is widely used in hydraulic transmission. When the servo hydraulic cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the servo hydraulic cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the servo hydraulic cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

servo hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the servo hydraulic cylinder head itself is the guide sleeve of the piston rod, the servo hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the servo hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

In the case of serious wear on the inner surface of the servo hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the servo hydraulic cylinder manufacturing process for replacement. The servo hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Answers to some questions about servo hydraulic cylinder:

Is it good or bad for the hydraulic cylinder working in the limit stroke position?
It is not good for the hydraulic cylinder working in the limit stroke position. Generally, when the cylinder is used in the limit stroke, the oil in the cylinder will form a backflow back pressure impact on the piston and guide sleeve seals. If the limit is not accurate, it is easy to cause collision damage. It is recommended to leave a buffer of ten to twenty centimeters.

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
色综大香蕉网| 一级黄片大鸡巴插逼里| 女人AV 1区二区| 闽侯县| 国产天仙自拍小视频| 日韩av在线一区| 日韩熟女操N合作| 五月婷婷原地址| 大鸡吧搞逼操屁股视频| 6090线午夜一区二区三区| 色婷婷五月在线免费观看视频| 日本超碰影院| 老熟女大屁股熟妇直播| 亚洲丝袜一二三| 国产区欧美区搭讪在线观看| 成人午夜美女性爱在线| 日本视频88| 鸥美日韩精品| 北条麻纪二区三区| 日韩爱爱精品视频| 大黑屌干大屁股| 日韩精品一二区宅男av| 就要狠狠干综合| 欧美在线日韩系列| www.白虎美女被大鸡巴操| 人妻有吗在线播放| 最新欧美日韩一级片| 日BB视频| 小穴毛在线观看| 日韩美女鸡吧| 亚洲国产成人A V| 欧美熟妇极品另类| 日韩成人小视频在线观看| 91精品无码少妇a 6 2v自慰| 超碰香蕉在线| 粉嫩虎白美女视频| 人妻 视频 日韩| 激情五月综合俺也去在线播放| 骚逼2区| 欧美激情淫荡在线视频| 制服丝袜淫水|