亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Burma

Release time:2023-11-24 16:13:18 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Burma trunnion cylinder

(Burma trunnion cylinder,produced by Hengyu Group)

trunnion cylinder are widely used in Burma,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Burma.

Introduction to trunnion cylinder:

In recent years, the processing process of the trunnion cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

The repair method of the trunnion cylinder: the repair of the trunnion cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

When the trunnion cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the trunnion cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the trunnion cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

In the process of using the trunnion cylinder, sometimes such a problem will occur, the trunnion cylinder can not act immediately after the instruction of the trunnion cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil trunnion cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about trunnion cylinder:

How to choose cylinder size, pump type, motor power for a 30-ton press?
30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.

How many boom cylinders, bucket rod cylinders and bucket cylinders are there in a small single-bucket excavator?
one for bucket, one for forearm, only one piece for a small excavator under the big arm, two pieces for medium and large excavator.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
蜜桃超碰在线观看| 极品福利视频一区二区| 少97大香蕉视频| 淫熟少妇人妻色综合| 大鸡吧操逼强奸| 婷久综合视频| 啊啊啊好大好痛好爽视频在线观看 | 色666av| 国产卡一卡二av| 和林格尔县| 男人区狠狠干| 有码视频在线播放网站| 日韩欧美一区二区在线| 逼白虎网站| 高潮 AV 不卡| 美国女人肏大屄视频| 亚洲v欧美v另类v综合v日韩v| 午夜无挡视频| 蜜乳视频在线免费观看| 欧美自拍视频网站极品| 青春草在线激情视频| 欧美日日操| 我不卡一区二区三区| 激情午夜久久| 操大逼网站美国黄色网| 日本无一区二区| 啊啊啊啊啊啊啊一区二区| 国语黄片播放| 国产极品尤物在线视频| 就爱大香蕉手机视频| 扣挖骚穴喷水无码| 华女AV一区二区三区| 男生鸡巴操女生骚逼免费视| 日韩第一页日韩欧美| 大香蕉凹凸视频免费| 五十路熟视频| 啊啊啊啊啊啊啊一区二区三区极品 | 在线91成人大鸡巴| 熟女诱惑一区二区成人影院| 无码骚逼视频| 少妇精品视频|