亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Tunisia

Release time:2023-11-24 08:39:28 Hits: Current position: Home > News

This article mainly introduces:

Tunisia hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Tunisia servo cylinder

(Tunisia servo cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo cylinder are widely used in Tunisia,because of long service life,smooth movement,high work efficiency.So our company has designed servo cylinder for customers from Tunisia.

Introduction to servo cylinder:

When the servo cylinder is installed, the piston and the servo cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the servo cylinder head boss is easy to cause scars when it hits the inner surface of the servo cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized servo cylinders, only careful and careful operation can be avoided.

The assembly work of the servo cylinder has a great impact on the quality of the servo cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The piston rod of the servo cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about servo cylinder:

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

What kind of seal ring we should choose for 120Mpa hydraulic cylinder?
The sealing rings used in mining machinery are high pressure, which can reach 150MPa. It is generally composed of three parts, the guide ring, the sealing body and the elastomer. It's not a special structure. It's more mature. Usually said mountain circle, bud circle.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲国产区一区二久久| 黑人一级操逼| 日韩黄片鸡巴| 日韩美和中国美女靠逼一一一一一一 | 欧美激情中文字幕一区二区三区| 青青草在线免费视频| 欧美三级高潮喷水| 超碰日韩字幕在线看| 欧美一级AA大片日韩| 激情五月播播深爱| 久久人妻露脸精品| 女性小穴国产| 中文字幕一区二区三区在线播放干一路 | 黄色在线中文字幕视频| 中文字幕免费精品一区二区三区| 亚洲日韩熟女人妻丝袜中文字幕| 日本操骚逼网| 插比91成人| 日韩,国产,欧美| 大香蕉伊人在线视频| 真人日逼可以看是平| 美亚洲精品第一大全射B视频| 神马午夜A片一区二区| 人妻中文原创字幕有码视频| 肥胖东北妓女高潮视频| 国产五月精品| 美女扒开尿道视频网站| 欧美日韩一期二期三期| 北岛玲直播在线| 日韩操逼视频网址| wwwxxx一区| 操b久久久久| 在线高清一区二区| 色久悠悠色久悠悠| 亚洲一区二区AV电影| 日本丰满老熟女视频| 大黑屌草白逼| 欧美激情中文字幕在线观看一区| 99成人无码鸡巴视频| 在线中日av| 国产大鸡巴骚b|