亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Congo

Release time:2023-11-23 08:22:51 Hits: Current position: Home > News

This article mainly introduces:

Congo hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Congo reset cylinder

(Congo reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in Congo,because of no need for deceleration device,long service life,smooth movement.So our company has designed reset cylinder for customers from Congo.

Introduction to reset cylinder:

The piston rod of the reset cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

The cavitation of the reset cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the reset cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

When the reset cylinder is customized, if there are high requirements for the quality of the reset cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the reset cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the reset cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When the reset cylinder is in use, ensure that the reset cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Answers to some questions about reset cylinder:

How to calculate the cylinder diameter, rod diameter and pressure of the cylinder, and how to output tonnage?
Hydraulic cylinder output force F=PAX10^3(KN) F is the output force (KN), P working pressure (MPa), A is the piston or plunger area of action.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
黑人疯狂输出挺进日本女人| 综合就爱网激情| 鸡巴操欧美| 乐平市| 欧美日韩一级免费破处| 我要操韩国美女白虎逼| 亚洲第一淫妇视频| 逼逼给你日视频免费看| 亚洲AV无码一区二区三区不卡毛片| 麻豆传媒一区二区精品视频在线观看| 啊啊啊好爽视频免费| 色哟哟一区二区在线观看| 大香交小黑逼天天操| 无遮挡黄片| 青春草逼视频| 淳化县| 国产三级激情在线视频| 久久九九性生活视频| 操逼逼视频啊啊啊啊哦哦哦哦| 嗯嗯啊啊啊嗯嗯视频在线观看 | 亚洲日韩精品一区二区三区高清| 黄片日韩有码| 青春草在线视频免费观看网站| 大鸡巴 网站| 逼逼逼www| AV日韩有码高清| 18禁美女无遮挡免费| .一区二区网站| 伊人色综合久久天天五月婷| 91久热亚洲一区二区| 在线国产一级少妇裸体洗澡自慰片| 美女夜夜春| 啊啊嗯enen视频| 日本40路熟妇| 欧州美女操逼视频| 大香蕉免费大香蕉精品莉| 国产抓奶舔阴高潮视频免费在线看| 饥渴人妻与黑人| 丁香蜜臀久久浪潮| 歐美操逼視頻| 最新欧美a网站|