亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hsgk cylinder Sold to Nigeria

Release time:2023-11-23 08:22:44 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,hsgk cylinder manufacturer,hsgk cylinder

Nigeria hsgk cylinder

(Nigeria hsgk cylinder,produced by Hengyu Hydraulic Cylinder Factory)

hsgk cylinder are widely used in Nigeria,because of long service life,smooth movement,high work efficiency.So our company has designed hsgk cylinder for customers from Nigeria.

Introduction to hsgk cylinder:

The difference between the plunger hsgk cylinder and the piston hsgk cylinder is that the piston in the hsgk cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type hsgk cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Classification of hsgk cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

The oil hsgk cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

How to determine the working pressure of the hsgk cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, hsgk cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about hsgk cylinder:

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

The diameter of the cylinder is 180mm and the pressure is 14mpa. How many tons can the cylinder hold?
Calculate the area of the cylinder, 3.14*9*9=254.34 square centimeters, take the approximate number of engineering, 1 mpa pressure is about 10 kg per square centimeter, 14 mpa pressure is 140 kg per square centimeter, that is 254.34*140=35607.6 kilograms, it can be known that the cylinder can be about 35 tons in theory.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产 精品 探花 熟女 视频| 大鸡巴插大逼里的高清视频| 超碰在线一区二区三区| 禁视频网站大全| 欧美美女阴部视频| 女人张开腿让男人桶桶到爽| 手机看片四房大香蕉| 欧美男插女视频| 内射白精一区二区三区| 无视频在线看| 色吊丝1| 高潮AV第一页| 国内胖女人操逼视频| 亚洲被操的大鸡巴| 成人片 三级韩国在线| 在线琪琪免费三级电影| 日韩玩弄小穴| 四区五区视频在线观看| 蜜桃AV大鸡吧| 欧美日韩国产一级毛片| 嗯嗯啊啊好水| 韩国无码性爱视频免费| 国产极品美女白虎无遮挡看个够| 黄色中文字幕在线看视频| 国产丝袜视频一区二区竹菊| 亚洲狠狠综合网| 五月激情婷婷五月| 鸡巴不卡逼视频| 骚鸡巴用力操我,爸爸用力视屏| 狂插入美女视频在线观看| 欧美大屌操逼网站| 超碰激情综合| 欧美一区二区三区爱爱视频| 国产成人在线不卡av| 鸡鸡搞逼逼逼免费视频| 99热亚洲8899熟女| 性爱博彩无码| 午夜成人中文字幕在线| 日韩三级大奶美女| 插逼AV网站| 人妻少妇91精品一区图片|