亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic gate cylinder Sold to Norway

Release time:2023-11-23 08:22:33 Hits: Current position: Home > News

This article mainly introduces:

Norway hydraulic cylinder,hydraulic gate cylinder manufacturer,hydraulic gate cylinder

Norway hydraulic gate cylinder

(Norway hydraulic gate cylinder,produced by Hengyu Hydraulic Cylinder Factory)

hydraulic gate cylinder are widely used in Norway,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed hydraulic gate cylinder for customers from Norway.

Introduction to hydraulic gate cylinder:

When the hydraulic gate cylinder is in use, ensure that the hydraulic gate cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

How to determine the working pressure of the hydraulic gate cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, hydraulic gate cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Do not regularly check the damage of the chrome layer of the hydraulic gate cylinder: completely extend the hydraulic gate cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the hydraulic gate cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the hydraulic gate cylinder seal. Welding slag is strictly prohibited on the surface of the hydraulic gate cylinder.

The repair method of hydraulic gate cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about hydraulic gate cylinder:

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲啪啪啪污日本| 18P色亚洲| 亚洲妓女口暴深喉69| 轻轻挺进新婚少妇身体里视频| 亚洲一区二区三区wwwav| 激情久久在线| 祥仔手机访问一区免费| 日本少妇中出| 国产一级传媒黄录像免费| 熟女人妻电影网| 老太太四区| 男生被操在线观看视频| 久久人妻。| 黑料网视频一区二区在线观看| 操逼在线看| 精品人体一区| 色婷婷激情五月91| 超碰在线免费福利视屏| 日本一二三区不卡精品免费视频| 亚洲一二三在线| 一道本日本日本日日天天日日日| 老司机精品视频在线一区二区| 有码一区视频| 人人操人人 国产| 大鸡巴爱艹逼视频| 冯妍门破处视频国产导航在线观看| 亚洲国产熟女99| 五月婷綜合| 午夜十八禁免费在线视频| 操逼视频入口处| 在线观看日本一不二不三不四不| 很操美女骚bbb| 骚逼性天堂| 来一段美女操逼的视频看看| 色av天堂| 精品欧美一区二区三区开肛| 午夜福利美女啪啪| 怡红院亚洲第一综合久久| 人午夜射精精品| 亚洲 欧美 丝袜 中文 综合| 白峰美羽一区二区欧洲在线播放|