亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to UAE

Release time:2023-11-23 08:22:26 Hits: Current position: Home > News

This article mainly introduces:

UAE hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

UAE supporting cylinder

(UAE supporting cylinder,produced by Hengyu Hydraulic Co., Ltd)

supporting cylinder are widely used in UAE,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed supporting cylinder for customers from UAE.

Introduction to supporting cylinder:

Improve the service life of the supporting cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the supporting cylinder (such as the supporting cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the supporting cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the supporting cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single supporting cylinder exhaust.

The supporting cylinder is not the same as the supporting cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the supporting cylinder can not be used as a high-power power component, but the supporting cylinder can be used as a relatively large power component, or the supporting cylinder system can be used.

The supporting cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the supporting cylinder, bite. Elimination method: When installing the supporting cylinder, ensure that the axis position of the supporting cylinder is consistent with the direction of movement; Make the load borne by the supporting cylinder as far as possible through the supporting cylinder axis, to avoid the phenomenon of eccentricity.

The assembly work of the supporting cylinder has a great impact on the quality of the supporting cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about supporting cylinder:

Where is the tension cylinder used in the excavator?
Get off the inside of the frame, behind the guide wheel (steering wheel, guide wheel). Disassemble the track and take the guide wheel out to see the tensioning cylinder (track spring).

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
五五月天激情在线资源| 在线老湿视频| 91精品亚洲一区| 麻豆视频自拍在线观看| 欧美精品一区二区三区午夜福利| 国产精品美女网址| 大鸡巴抽插小穴视频网| 亚洲熟女深插| 美国操BA片视频| 美女丰满后入一区五区| 天天干天天操美女夜夜狠| 大鸡吧艹骚逼| 美女永久免费视频| 贡觉县| 日韩欧美干| 大鸡巴把小穴插的爽在线视频| 全国18大,啪啪视频| 日本操逼视频大香蕉| 91制服丝袜电影| 曰韩热插| 欧美日韩精品AAAA免费大片| 祥仔手机av| 操逼看片视频国产91| 鄂州市| 性感美女被大鸡巴看| 天天爽,夜,夜爽视频| 办公室护士毛片| 欧美伦乱又伦| 9色激情蜜臀| 日韩久久久久综 合| 国产一区二区天美| 国产小情侣激情视频| 亚洲一区二区三区美女啊啊啊啊 | 日日骚不卡| 日韩美女自慰BBB| 九九九精品一区三区| 大鸡巴爆肏嫩逼| 中日韩一区二区视频 | 人妻少妇久久电影免费观看中文字幕| 日韩视频精品| 国产淫荡视频|