亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic shear cylinder Sold to Uruguay

Release time:2023-11-08 08:12:17 Hits: Current position: Home > News

This article mainly introduces:

Uruguay hydraulic cylinder,hydraulic shear cylinder manufacturer,hydraulic shear cylinder

Uruguay hydraulic shear cylinder

(Uruguay hydraulic shear cylinder,produced by Hebei Hengyu company)

hydraulic shear cylinder are widely used in Uruguay,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed hydraulic shear cylinder for customers from Uruguay.

Introduction to hydraulic shear cylinder:

hydraulic shear cylinders in series, parallel and series parallel. Series: In the hydraulic shear cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the hydraulic shear cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the hydraulic shear cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the hydraulic shear cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

The repair method of hydraulic shear cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The hydraulic shear cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the hydraulic shear cylinder should pay attention to: the operation should be as far away from the hydraulic shear cylinder as possible, to avoid falling objects, knocking, rubbing the hydraulic shear cylinder coating. When cleaning the hydraulic shear cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the hydraulic shear cylinder when the oil temperature exceeds 70 ° C.

The hydraulic shear cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the hydraulic shear cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The hydraulic shear cylinder is basically composed of hydraulic shear cylinder and hydraulic shear cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

Answers to some questions about hydraulic shear cylinder:

Can multiple identical hydraulic cylinders be supplied with the same supply line?
This can be connected, but there is a disadvantage, that is, the hydraulic cylinder with the minimum pressure is extended first, and then the pressure is higher, and then the higher, until all the hydraulic cylinders are extended, which may not meet the requirements of field use.

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日熟女网站| 被大鸡巴操的在线视频| 中文字幕石原莉奈| 日本大香蕉在纸线| 欧美草逼草一区| 日本五月天网| 深夜啪啪啪软件| 国产av成人一区| 欧美熟交一区二区三区| 91经典三级片| 欧美成人在线黄片| 夜上海AV网站| 大鸡巴操骚逼视频摸大奶| 日韩后入美女| 东京热日本视频| 大,大鸡巴操逼的视频 | 91视频精品一区二区三区| 精品人妻伦一二三区久久简爱| 欧美中日韩逼逼| 青春草手机在线免费视频| 激情欧美人妻| 日本美女乱伦视频| 欧美熟女精品在线| 一级欧美片日韩片| 手机大香蕉在线视频| 在线播放大鸡巴| 欧美小穴在线免费观看| 女V中文字幕操你| 五月性爱片| 91精品无码免费高清一区二区无码| 欧美之大香蕉| 在线国产无码高清哈哈| 男人把女人捅到暴爽免费| 日韩在线麻豆传媒网站视频| 亚洲女人的大黑b| 操人视频动漫免费观看 | 大香蕉手机在线视频日韩在线| 大鸡巴插小逼免费视频| 熟女露脸一区| 自拍偷拍 人妻熟女 亚洲| 激情啪啪啪网站|