亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Germany

Release time:2023-11-21 09:56:28 Hits: Current position: Home > News

This article mainly introduces:

Germany hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Germany stacker cylinder

(Germany stacker cylinder,produced by Hebei Hengyu company)

stacker cylinder are widely used in Germany,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed stacker cylinder for customers from Germany.

Introduction to stacker cylinder:

The definition of the minimum stable speed refers to the minimum movement speed of the stacker cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the stacker cylinder that undertakes different work has different requirements for the minimum stable speed.

When the stacker cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the stacker cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

When the stacker cylinder needs to be stored for a period of time, please follow the recommended methods: The stacker cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the stacker cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil stacker cylinder should not be in direct contact with water vapor for a long time. The stacker cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the stacker cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the stacker cylinder Before working, the stacker cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the stacker cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The difference between the plunger stacker cylinder and the piston stacker cylinder is that the piston in the stacker cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type stacker cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Answers to some questions about stacker cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
自拍偷拍国产主播| 嗯啊嗯啊好舒服中文字幕| 福利盒子自拍| 白虎美女被插网站在线观看| 日韩 在线 欧美| 深泽县| 美女无毛粉红小逼一线天馒头逼| 日韩精品手机在线视频| 可乐福利区在线看| 国产又粗又长又爽的视频网站| 操 女人的逼亚洲| 深夜操BAV| 甘南县| 亚洲成人狠狠| 啊啊啊好爽操我啊啊啊视频网站| 秋霞电影国产在线二区| 亚洲无码 校园春色 在线| 国产美女操逼操逼| 国产在线嗯嗯嗯啊啊啊| 吃瓜视频在线视频你懂的| 黄色网络中文字幕日本| 超碰超碰超碰超碰超碰超碰大香蕉| 亚洲美女日韩精品熟女| 日韩 欧美 国产 视频 激情| 精品人妻少妇一区偷拍| 日本大屁股人妻| 超碰特在线| 97精品大香蕉在线| 大鸡巴久鲁国产在线| 操骚一| 日本黄色片网址大全一区二区| 亚洲天堂黄片| 日本嗯嗯小视频在线观看| 91操白虎网站| 久久国产夫妻视频| 亚洲综合色婷婷六月丁香宅男| 免费看性生活一级视频| 黑丝自慰在线| 亚洲五码电影| 美女张开黄色网| 一级黄片果冻传媒捉奸在床板|