亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Croatia

Release time:2023-11-21 09:56:26 Hits: Current position: Home > News

This article mainly introduces:

Croatia hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Croatia tailplate hydraulic cylinder

(Croatia tailplate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailplate hydraulic cylinder are widely used in Croatia,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed tailplate hydraulic cylinder for customers from Croatia.

Introduction to tailplate hydraulic cylinder:

After chrome plating of the piston rod of the tailplate hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Before the tailplate hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

tailplate hydraulic cylinder use should try to avoid sealing belt into the tailplate hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the tailplate hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the tailplate hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The tailplate hydraulic cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the tailplate hydraulic cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the tailplate hydraulic cylinder wall due to the stiffness and the weight of the parts, causing scars.

Answers to some questions about tailplate hydraulic cylinder:

Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
九七超碰碰| 福利成人在线| 好吊日殴美| 五月婷婷丁香色| 午夜精品一区二区三区免费软件| 久久五夜| 啊啊啊好爽嗯嗯视频| 想吃爱爱视频网站| 亚洲av无码h一区二区| 欧美激情男人天堂| 保康县| 欧美极品 日韩 白虎| 蜜桃语音AV| 木下凛凛子JUL931中文字幕| 一区二区三区抡理视频| 元氏县| 午夜xxxxxxx| 波多野结衣操大奶| 嗯嗯啊啊啊操逼视频| 六十路不卡| 国产淫妇重口另类直播在线| 亚洲国产一区理论高清| 91在线观看一区二区三区| 男子操女生915568| 视频91日产蜜臀| 啊啊太大了视频大全| 亚洲精品操比视频| 美欧色频区| 亚州AV一二三区| 夫妻黄色一级片| 日韩在线不卡在线| 日韩a一级欧美一级| 大鸡吧插小穴视频重口| 色悠悠婷婷综合中文在线| 爱爱网久久| 黑人无码大战亚洲女人| 骚逼求操视频| 美女露点乳头洗澡一区二区三区| 骚逼自拍视频网| 青青大香蕉成| 国产欧美日韩中文字|