亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to Costa Rica

Release time:2023-11-21 09:56:01 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

Costa Rica push and pull the cylinder

(Costa Rica push and pull the cylinder,produced by Hengyu Hydraulic Cylinder Factory)

push and pull the cylinder are widely used in Costa Rica,because of long service life,smooth movement,high work efficiency.So our company has designed push and pull the cylinder for customers from Costa Rica.

Introduction to push and pull the cylinder:

How the cavitation of the push and pull the cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the push and pull the cylinder, resulting in corrosive damage to the parts.

In use, the push and pull the cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the push and pull the cylinder.

When the push and pull the cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the push and pull the cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

When installing the push and pull the cylinder pipe, the pipe should be cleaned after installation, and should not pass through the push and pull the cylinder block, and the by-pass pipe must be installed in front of the oil port of the push and pull the cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the push and pull the cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the push and pull the cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about push and pull the cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩高跟美女日逼视频| 丁香五月婷婷av| 日本久久美女网| 性插视频| 国产曰韩亚洲一级大片| 肉丝袜内射一区二区| 天堂欧美黄色| 激情都市综合五月| 在线免费观看嗯嗯嗯啊啊啊视频 | 最近中文字幕视频一区二区三区| 91粉色在线观看| 色开心激情成人| 内地日韩欧美小视频| AV成人在线免费观看| 人人襙人人爽| 中文字幕人妻一区二区三区熟女| 九久热无码免费视频| 久国产一二| 久久精品爱悠悠| 欧美性放荡在线观看| 亚洲一区二区三区991| 嗯,操的好舒服,好爽视频| 高清AV在线一区二区三区| 五月婷婷,中文字幕| 日韩成人五月天| 舔骚逼奶头舒服视频啊啊啊啊啊啊| 国产后入在线视频| 少妇自慰到爽| 抽插 不卡 av| 丁香超碰在线观看| 台湾佬中文娱乐22ⅩX| 精品人妻一区二区9厂| 小穴 偷拍自拍| 鸡巴爆草女骚货| 国产日韩欧美在线视频色欲| 午夜一区二区三区蜜桃视频| 男女爱爱免费视频网站| 插进去无码视频| 日本高清成人视频一区二区三区| 视频1区2区中文字幕人妻日韩 | 日本黄色有码视频网站|