亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Uganda

Release time:2023-11-21 09:55:59 Hits: Current position: Home > News

This article mainly introduces:

Uganda hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Uganda stern plate hydraulic cylinder

(Uganda stern plate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

stern plate hydraulic cylinder are widely used in Uganda,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stern plate hydraulic cylinder for customers from Uganda.

Introduction to stern plate hydraulic cylinder:

stern plate hydraulic cylinder and hydraulic station selection: Select the type and structure of the stern plate hydraulic cylinder according to the operation requirements of the main engine. According to the external load force borne by the stern plate hydraulic cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the stern plate hydraulic cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the stern plate hydraulic cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the stern plate hydraulic cylinder, the diameter of the piston and the piston rod.

When the stern plate hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

stern plate hydraulic cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards stern plate hydraulic cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the stern plate hydraulic cylinder guide is determined by the length of the stroke. Check the strength of stern plate hydraulic cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

Before the stern plate hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

Answers to some questions about stern plate hydraulic cylinder:

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91精品无码少妇高潮喷水白浆 | 欧韩又粗又硬| 精品高清自拍| 麻豆蜜臀av| 亚洲肛交免费视频播放网站| 亚洲区在线观看天美| 多人操逼日韩| 菏泽市| 欧美极品 日韩 白虎| 小穴不行了视频| 亚洲中老年性生活视频在线| 麻豆果冻传媒在线观看视频免费入口 | 性玩视频一区二区| 人妻91精品久久久久| 亚洲视频一区二区三区免费观看视频 | 女人呗操视频91| 人妻一区二区国产高清七色| 子长县| 666AV资源| 日本户外一区二区网站| 伊人操逼群| 今晚狠狠干| 午夜福利视频夸克| 婷婷五月大片| 制服丝袜欧美日韩| 美女视频网站白虎| 青娱乐日本性爱| 深夜AV社区| 小穴挨操视频| 男操女逼软件91| 灌南县| 国产视频一区二区三区在线大鸡| 绝色91在线| 国产又大又粗又猛又黄又爽| 成人av一线免费观看| 保康县| 午夜伦理 一区二区| 五月婷99综合| 综合激情专区| 大神呆哥精品视频在线一区二区| 天天干天天做天天干天天做|