亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Tunisia

Release time:2023-11-21 09:55:58 Hits: Current position: Home > News

This article mainly introduces:

Tunisia hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Tunisia tailplate hydraulic cylinder

(Tunisia tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailplate hydraulic cylinder are widely used in Tunisia,because of no need for deceleration device,no transmission clearance,long service life.So our company has designed tailplate hydraulic cylinder for customers from Tunisia.

Introduction to tailplate hydraulic cylinder:

The piston rod of the tailplate hydraulic cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

When using the tailplate hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the tailplate hydraulic cylinder block. If the tailplate hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the tailplate hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the tailplate hydraulic cylinder, so that the working efficiency of the tailplate hydraulic cylinder is reduced.

The cavitation of the tailplate hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tailplate hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

If the seal of the tailplate hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Answers to some questions about tailplate hydraulic cylinder:

What is the material of the hydraulic cylinder slider?
Three parts of the hydraulic cylinder are essential, which are: cylinder - cylinder head assembly, piston - piston rod assembly, and sealing device. When you say slider, you mean piston. - Piston rod. Piston materials commonly used gray cast iron, wear-resistant cast iron, aluminum alloy (assembled), etc., can also be used 35 and 45 steel (integral). The piston rod is generally made of 35 and 45 steel. When the impact vibration is large, alloy steel such as 55 steel or 40Cr is used.

When there is only one hole in the oil inlet and outlet of the hydraulic cylinder, will there be oil leakage?
It is a single acting oil cylinder. This oil cylinder is always driven by hydraulic oil in advance, and is generally pulled back by the spring at the bottom of the piston or the weight of the cylinder piston or the load. But either way, it has nothing to do with any internal leakage. Whether the oil is internally drained is related to the sealing and accuracy of the cylinder itself.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操操操一区二区三区| 35pao视频男人的天堂一区| 日本福利小视频| 美日韩少妇肥胖老太太视频一二三区 | 日韩妇自慰| 亚洲 午夜 福利 成人| 91精品成人蝌蚪porny在线| 欧美无删减视频日韩免费| 99热色久亚洲片| 狂干少妇视频| 嗯啊嗯嗯啊在线观看| 成人AV字幕精品| 操操大骚逼逼| 中國一區二區三區四區av| 日本东京热电影麻豆传媒| 韩国福利视频一区二区| 欧美综合在线观看女| 虐逼高潮出水大鸡巴| 一区二区三区麻豆蜜桃| 在线视频免费播放十一区| 超碰直播中文字幕| av亚洲激情| 草草亚洲AV成人片| 日本女人被黑人大吊操| 性感大鸡巴操美女小骚逼大骚逼骚逼逼 | 大香焦大美女日B| 国产国产乱老伦熟妇视频| 我爱Av一区二区三| 亚洲欧美婷婷射人人妻| 白丝麻麻被操。| 日本黄视频呗一区二区| 亚洲vs日本vs欧洲免费一区 | 妓女自由AV| 国产夫妻偷拍自拍一区| 公主岭市| 欧美国产日韩图片小说| 一区 二区 4k av| 色婷婷 免| 免费看日粉嫩B视频| 成人一区二区三区暧昧视频| 欧美,国产视频|