亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steel mill cylinder Sold to Dominica

Release time:2023-11-21 09:55:55 Hits: Current position: Home > News

This article mainly introduces:

Dominica hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

Dominica steel mill cylinder

(Dominica steel mill cylinder,produced by Hebei Hengyu company)

steel mill cylinder are widely used in Dominica,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed steel mill cylinder for customers from Dominica.

Introduction to steel mill cylinder:

The steel mill cylinder is not the same as the steel mill cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the steel mill cylinder can not be used as a high-power power component, but the steel mill cylinder can be used as a relatively large power component, or the steel mill cylinder system can be used.

The quality of the steel mill cylinder can not be ignored in the purchase of the steel mill cylinder. The steel mill cylinder is the main component of the steel mill cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. steel mill cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of steel mill cylinder is deep hole processing, which has always troubled the processing personnel.

In order to ensure the service life of the steel mill cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

How to determine the working pressure of the steel mill cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, steel mill cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about steel mill cylinder:

What are the main dimensions of the cylinder?
The main dimensions of the cylinder include: cylinder inner diameter, piston cylinder diameter, cylinder length, cylinder wall thickness, stroke, installation distance, etc.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女18黄逼逼| 黑屌亚洲少妇| 熟女69式在线播放| 欧美美女丈鸡巴| 操丰满少妇18p| 暴操极品白丝91| 日韩大鸡| 日本女人逼逼视频看看| 操欧美小少妇| 日韩、欧美一级片| 一级AV网站| av男人的午夜网| 午夜福利二级视频| 竹北市| 免费观看一区二区三区| 少妇视频二区| 美女亚洲一二区| 大奶子在线观看欧美| 亚洲熟91| 欧美熟妇在线观看| 中文在线播放一区二区三区不卡| 第一福利在线观看永久视频| 玩弄极品少妇人妻老师91| 20,99狠狠干| 91视频婷婷五月天| 在线一区二区不卡av电影| 日韩男女久久久| 一级黄色。大片| 久久久嗯啊| 淫乱人妻精品一区二区| 一级黄片视频韩国大鸡巴操| 狠狠视频一区| 91黄页网| 亚洲欧美另类在线观看你懂的| 日韩又黄又刺激裸交视频在线观看网站 | 操大骚逼Av中文| 大鸡巴操人妻91短视频在线| 欧美,日韩一级片在线观看| 鸡吧插入逼逼免费视频| 亚洲性插二区| 美女被插视频网站|