亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Canada

Release time:2023-11-08 08:12:11 Hits: Current position: Home > News

This article mainly introduces:

Canada hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Canada swager cylinder

(Canada swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Canada,because of high work efficiency,excellent fatigue and impact resistance,smooth movement.So our company has designed swager cylinder for customers from Canada.

Introduction to swager cylinder:

Analysis of commonly used seals: The wear ring and slip ring commonly used on the swager cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

swager cylinder body inspection: The inner surface of the swager cylinder and the piston seal are the main factors causing the leakage in the swager cylinder, if the swager cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the swager cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

When installing the swager cylinder pipe, the pipe should be cleaned after installation, and should not pass through the swager cylinder block, and the by-pass pipe must be installed in front of the oil port of the swager cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the swager cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the swager cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Classification of swager cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

Answers to some questions about swager cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

What is the function of the Reza mounted master cylinder?
The role of the Resa-mounted master cylinder is to pump the concrete from the hopper to the delivery pipe and to provide sufficient concrete outlet pressure so that the concrete can reach the specified location.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久我要操| 午夜福利久久福利视频久久| 操逼视频网站在线观看免费| 亚洲第一艹逼| 操我啊啊好舒服免费视频| 91在线观看一区二区三区| 欧洲中文字幕久久| 天堂久久天堂色综合色| 子长县| 专门在线看美女的网站| 非洲一区视频| 中国农村老熟女2| 小穴抽搐视频在线观看| 色香蕉婷综合| 日韩欧美P片久久| 国产探花色| 白浆福利视频网| 天天日一日天天操一操| 九九插穴| 亚欧视频91| 在线观看自拍视频一区二区精品| 开心色国产激情国产激情国产亚洲| 精品少妇人妻A乱色熟女| 婷婷 综合 五月 欧美 自拍| 亚洲综合色婷婷六月丁香宅男| 不卡一卡二区| 日韩在线视频 麻豆| 抽插美女91| 日本一区二区性爱网站| 91大神视频在哪里能观看| 狠操白虎美女视频| 老司机视频手机看片| 1区二区三区日韩欧美黄色网址| 日韩视频第一页91家庭小说 | 日B视频网站在线看| 看美女操逼视频免费的| 美眉艹大鸡巴| 丰乳肥臀熟女一区二区三区| 国内AV在线亚洲蜜桃观看| 老司机精品视频在线观看入口| 另类少妇综合网一区|