亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Poland

Release time:2023-11-20 09:49:45 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Poland servo cylinder

(Poland servo cylinder,produced by Hebei Hengyu company)

servo cylinder are widely used in Poland,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed servo cylinder for customers from Poland.

Introduction to servo cylinder:

The wear of the hard chromium plating layer of the servo cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

How to repair the servo cylinder body when it is damaged: When the servo cylinder has trace deformation and shallow tensile marks, the servo cylinder is repaired by strong honing process. The heavy honing process can repair servo cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the servo cylinder can meet the technical requirements.

The definition of the minimum stable speed refers to the minimum movement speed of the servo cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the servo cylinder that undertakes different work has different requirements for the minimum stable speed.

servo cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the servo cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about servo cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩欧美剧情在线成人| 午夜优质福利| 操逼视频大鸡巴| 黄色激情国产| 国产熟女一区二区三区9楼| 五十路毛茸茸中文字幕| 操小B小视频| 欧美亚洲韩国操逼| 啊啊啊啊视频好舒服| 激发美女青春骚逼被操| 成人区人妻精品一区二区蜜柚| 欧美丝袜视频一区二区| 大香蕉手机看片日本| 欧美少妇熟女免播放| 日韩欧美操逼吃鸡巴| 草草草免费视频| 欧美,日韩一级片在线观看| 大棒日美女逼免费视频| 高级亚洲成人色情网站| 日韩成人AV动漫在线| 熟妇骚穴AV| www3女又叉又| 久久艹口爆| 美女18操鸡网站| 鸡吧和逼的视频| 加勒比,东京热中文字幕| ed2k久久一区| 精品传媒在线看| 老熟妇一区二区三区六区| 色涩涩综合| 大鸡巴操死她免费观看| 日本一区二区三区不卡区| 熟女精品3| 大鸡巴干丰满美人妻| 三级片在线视频| 美女被男生操网站| 91yqeqsqzx| 淫妇骚穴视频| 大鸡巴把小骚逼操出水| 嗯嗯嗯……啊啊啊在线播放| 意大利大鸡巴又粗又长视频 |