亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steel mill cylinder Sold to Burma

Release time:2023-11-20 09:49:23 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

Burma steel mill cylinder

(Burma steel mill cylinder,produced by Hengyu Group)

steel mill cylinder are widely used in Burma,because of high work efficiency,long service life,smooth movement.So our company has designed steel mill cylinder for customers from Burma.

Introduction to steel mill cylinder:

steel mill cylinder and hydraulic station selection: Select the type and structure of the steel mill cylinder according to the operation requirements of the main engine. According to the external load force borne by the steel mill cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the steel mill cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the steel mill cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the steel mill cylinder, the diameter of the piston and the piston rod.

When the control pressure of the hydraulic system is too low, the steel mill cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The commonly used buffer structure of the steel mill cylinder is composed of a piston boss and a steel mill cylinder head groove. When the piston moves close to the steel mill cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

The machining accuracy of the steel mill cylinder depends on the level of equipment, production technology and testing means. steel mill cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

Answers to some questions about steel mill cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲国产熟妇一区 | 日韩在线字幕熟妻| 美女被躁到**嗷嗷叫视频| 女人无遮挡网站大全| 国产凹凸大香蕉| 国产激情av在线导航| 夜夜干,夜夜爽| 日韩高清在线一区福利姬| 成人国成人国产av| 国产传媒在线/欧美| 久久五月了香合激情| 延吉市| 欧美熟妇潮喷 91| 美女燥逼全屏| 亚洲一区成人AV| 五月婷婷丁香综合欧美| 欧美三区四区啊啊啊啊啊啊啊| 日本精品97视频| 欧美日韩操鸡吧操| 日韩精品免费一区二区高清精品 | 新疆成人影视一区二区三区| 国产原创肛交| 色婷婷免费观看视频在线| 亚洲有码1中文字幕| 特黄片免费看q| 青青草原精品视频在线观看| 操逼操起来| 欧美黑丝色一乱| 福利美女网站国产| 婷婷婷一级大片| 亚洲人一区二区三区胖女人| 91久久久人妻精品国产一区二区| 人人操碰日韩91| 无码一区二区三区不卡视频| 色呦色呦精品| 人妻斩り60歳无码| 内射白精一区二区三区| 成人免费网站久| 免费福利网址视频| 尤物人妻在线| 五月综合日韩亚洲|