亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Poland

Release time:2023-11-20 09:49:19 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Poland self-locking hydraulic cylinder

(Poland self-locking hydraulic cylinder,produced by Hengyu Group)

self-locking hydraulic cylinder are widely used in Poland,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed self-locking hydraulic cylinder for customers from Poland.

Introduction to self-locking hydraulic cylinder:

self-locking hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

If the piston rod and self-locking hydraulic cylinder are stuck or the self-locking hydraulic cylinder is blocked, at this time, no matter how to operate, the self-locking hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the self-locking hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

self-locking hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching self-locking hydraulic cylinder block - fine boring self-locking hydraulic cylinder block - grinding self-locking hydraulic cylinder block. The rolling method is: broaching self-locking hydraulic cylinder block - fine boring self-locking hydraulic cylinder block - rolling self-locking hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the self-locking hydraulic cylinder block is about 1-2 days, rolling 1 meter of the self-locking hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the self-locking hydraulic cylinder increases by 25%. If the self-locking hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality self-locking hydraulic cylinders, you must take the rolling production process. After the self-locking hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The difference between the integral self-locking hydraulic cylinder and the split self-locking hydraulic cylinder: The integral self-locking hydraulic cylinder and the split self-locking hydraulic cylinder in the self-locking hydraulic cylinder are two different self-locking hydraulic cylinders, and they are very different. The whole self-locking hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split self-locking hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and self-locking hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

Answers to some questions about self-locking hydraulic cylinder:

Hydraulic cylinder performance requirements?
Hydraulic cylinder performance requirements: hydraulic cylinder is the hydraulic system to achieve energy transfer, conversion and control of the working medium, in addition, it is also responsible for the lubrication of the system, rust prevention, corrosion prevention and cooling. The performance of hydraulic oil will make the system flexible, accurate and reliable. Hydraulic performance requirements are determined according to the design parameters of the hydraulic system, operating conditions, the structure of the hydraulic pump and the working environment. Appropriate viscosity and good viscosion-temperature performance Viscosity is an important performance indicator of hydraulic pressure, which has an important impact on the smooth operation of the hydraulic system and the friction parts. The low temperature performance of hydraulic oil includes three aspects: low temperature flow, low temperature start-up and low temperature pumping.

Why are two cylinders not balanced with the balance valve?
Balancing valve is only suitable for occasions with low synchronous accuracy requirements, and proportional valves are recommended for occasions with high precision requirements.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产美女被c在线观看| 亚洲一卡二卡三卡亚洲一区二区三区 | 亚洲操逼大全| 高清中文字幕一区二区三区在线观看 | 五莲县| 欧美淫妇色色| 日韩精品手机在线视频| 日本韩国黄色录像| 欧美亚洲操逼网站| 成都市| 国产精品久久久海角社区| 欧美人妻在线观看免费| 欧美日韩国产高清在线不卡 | 日韩欧美人妻精品二区| 欧美操逼视频图片| 91熟女在线直播网站| 美女18禁一区二区三区视频| 啊啊啊嗯嗯在线免费观看视频 | www欧美狠狠干| 色四导航| 刘玥在线观看一区二区三区| 999污污污久久久| 骚逼小视频资源| 国产草逼骚逼| 欧美缴情啪综合缴情| 成熟风骚一区| 91大香蕉在线| 轻轻操免费视频1| 人妻最新中出| 国产精品农村夫妻自拍内射视频免费试看| 电影av一区二区三区三州| 操逼网站男女| 欧美大骚比| 看大鸡巴操逼视频| 怡红院Av人人爱| 轻轻操免费视频1| 99婷婷超碰| 三逼视频| 精品蜜臀一区二区| 大鸡巴日必内射视频| 让你白白操的网站|