亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Britain

Release time:2023-11-20 09:49:18 Hits: Current position: Home > News

This article mainly introduces:

Britain hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Britain reset cylinder

(Britain reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in Britain,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed reset cylinder for customers from Britain.

Introduction to reset cylinder:

reset cylinder hydraulic oil selection: The recommended working oil viscosity of the reset cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

The wear of the hard chromium plating layer of the reset cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

reset cylinder use should try to avoid sealing belt into the reset cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the reset cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the reset cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The method of sleeve reset cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the reset cylinder can be significantly improved by rolling in the finishing of the inner holes of the reset cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Answers to some questions about reset cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

In a hydraulic system, a hydraulic pump has many hydraulic cylinders and hydraulic motors, and these executive components do not coordinate their actions with each other.
A load-sensitive variable pump can be used if these components sometimes need to work simultaneously and the power required is large. The required flow is distributed by the multi-way reversing valve, and the required flow and pressure changes are automatically adjusted by the hydraulic pump. Pressure reducing valves can be used for particularly low pressure circuits. Because you execute more components, the use of quantitative pump will cause a waste of energy, the system heat is large, not suitable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
又大又粗操逼视频| 国产精品啪啪啪澡堂| 亚洲av天天拍| 骚逼喷水 91| 啊啊啊,插进来,好爽,还要视频| 嗯嗯操的我小逼逼好舒服的视频| 大鸡吧操小骚逼了| 中文字幕在线观看juy| 超碰情侣偷拍| 91大神免费精品视频| 国产一区亚洲精品成人| 日本成人一区二区三区网站| 欧美女人的天堂一二区| 国产又爽又黄又粗又大的视频| 视频小操逼啊啊啊啊啊啊| 午夜岛国影视| 不用下载就能免费看黄的网站一区| 嗯啊啊我要视频| 日韩美女逼网| 手机看片偷拍福利大屁股| 激情六月婷婷月| 女厕偷拍一区| 夫妻黄色录像韩国| 日本不卡二抠区| 日本女优不卡一区二区| 日本少妇内射视频| 一区二区三区中文伦理| 中英文一区二区成人网站| 超碰在线猛戳| 嗯嗯啊啊午夜视频流水| 精品大胸在线视频| 欧美一区日逼网站| 日本在线黄色H| 欧美白浆白虎| 日本操逼操穴视频| 中文字幕乱码亚洲无线码按摩| 亚洲欧美一区老妇| 亚洲啪啪自拍| 激情涩图午夜啪啪| 人妻 AV 一区二区三区| rihanchengrenyiji|