亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Kenya

Release time:2023-11-08 08:12:08 Hits: Current position: Home > News

This article mainly introduces:

Kenya hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Kenya series synchronous cylinder

(Kenya series synchronous cylinder,produced by Hengyu Group)

series synchronous cylinder are widely used in Kenya,because of long service life,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed series synchronous cylinder for customers from Kenya.

Introduction to series synchronous cylinder:

Before the series synchronous cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

When the series synchronous cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the series synchronous cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

The repair method of the series synchronous cylinder: the repair of the series synchronous cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Most of the failure of the series synchronous cylinder is because there is a foreign body in the series synchronous cylinder into the failure of the series synchronous cylinder, the most problematic is that it is difficult to determine when the foreign body is into the series synchronous cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about series synchronous cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

How to distinguish the size of hydraulic cylinder cavity?
The hydraulic cylinder has a rod cavity and a rodless cavity. The rod cavity is the cavity that the piston rod extends out. The rod cavity is of course small due to the existence of the piston rod. That's just relative.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女被操的网站| 亚洲综合欧美亚洲精品| 欧美精品另类日韩国产欧美| 人妻斩中文无码| 成人黄色大片儿免费吃瓜| 骚妣精品在线观看| 少妇扣逼网站| 武亱二区不卡| 日本玖玖| 吊打一区二区三区视频| 日本色诱一区二区三区| 日本 五十路熟| 欧美淫荡在线| 操B搞鸡网| 国产探花一区| 蜜臀av午夜一区二区三区gif| 成人男女午夜福利| 婷婷激情二区| 欧美自拍日本乱.伦视频| 大逼美女网站| 久久香蕉91| 亚洲一区二区三区不卡岁禁| 人妻地狱一区二区三区| 嗯嗯嗯嗯啊啊啊啊在线观看视频| 骚逼一区二区网| 五月婷婷丁在线播| 男女抽插视频无码十八岁禁| 神马在线午限福利限制一区二区三区| 青青草久久久黄色片| 日韩大香蕉综合视频| 深爱五月激动情网在线视频| 看逼逼尿尿| 黑人av一区二区三区| 婷婷第五色| 成人黄色3D网站在线| 美女的逼被操网站| 中文无码成人动漫制服丝袜| 十区十一区淫视频| 偷窥91高清一区二区三区| 亚洲另类精品一二区| 亚洲无码av二区三区|