亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Bulgaria

Release time:2023-11-20 09:49:13 Hits: Current position: Home > News

This article mainly introduces:

Bulgaria hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Bulgaria tension cylinder

(Bulgaria tension cylinder,produced by Hengyu Hydraulic Co., Ltd)

tension cylinder are widely used in Bulgaria,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed tension cylinder for customers from Bulgaria.

Introduction to tension cylinder:

If the seal of the tension cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

tension cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

tension cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The cavitation of the tension cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tension cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about tension cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

What is a mold core cylinder?
Simple plastic parts can be directly pushed out by the ejector rod after injection molding, complex plastic parts can not be directly pushed out by the ejector rod after injection molding, to make the interference part active, control its position through the cylinder (injection molding into the mold, so that the shape of the plastic parts meet the demand, exit after opening the mold, so that the plastic parts are smoothly pushed out), This kind of cylinder is the mold core cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产导航精品视频一区二区 | 美女动态网站亚洲后| 天天操天天夜夜| 啊,疼,操我视频| 久久精品少妇中文系列| 怡红院电影院一区二区| 苹果性感国产一区二区| 韩日黄片在线| 91人人人妻| 深夜福利男女激情啪啪网站| 黄色S色在线观看的免费| 大鸡巴操的好爽网站| 熟女导航网址| 亚洲日韩第一区在线观看| 日本精品熟女| 亚洲 欧美 中文 另类| 被男人大鸡吧插逼逼视频| 99热色情| 在线观看成人黄色很色很黄很污网站| 亚洲美日韩成人片| 亚洲多毛熟女视频| 亚洲色图你色我| 福利大香蕉视频在线观看| 中文巨乳大香蕉| 精品96国产一区| 都市激情 麻豆 蜜桃| 亚洲无码avwang三区| 亚洲熟妇 码视频| 性加勒比熟女人妻| 中文字幕,制服诱惑视频在线观看| 国产黄片欧美黄片精品| 视频欧美人妻日韩| 五月嗷嗷综合| 欧美 日韩 国产 夫妻 精品 在线| 蜜乳精品在线| 可以看的AV片| 国产AV色区| 无码肛交在线| 美女逼久久| 艳照门一区三区| 鸡巴插小穴手机在线视频|