亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

folding machine cylinder Sold to Australia

Release time:2023-11-19 14:07:01 Hits: Current position: Home > News

This article mainly introduces:

Australia hydraulic cylinder,folding machine cylinder manufacturer,folding machine cylinder

Australia folding machine cylinder

(Australia folding machine cylinder,produced by Hengyu Group)

folding machine cylinder are widely used in Australia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed folding machine cylinder for customers from Australia.

Introduction to folding machine cylinder:

The folding machine cylinder should be vented: when the folding machine cylinder is installed or parked for a long time to work again, the air will penetrate into the folding machine cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the folding machine cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the folding machine cylinder, the oil is best entered and discharged from the highest point of the folding machine cylinder. folding machine cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When the initial action of the folding machine cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the folding machine cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

folding machine cylinder is the most important part of construction machinery, the traditional processing method is: broaching folding machine cylinder block - fine boring folding machine cylinder block - grinding folding machine cylinder block. The rolling method is: broaching folding machine cylinder block - fine boring folding machine cylinder block - rolling folding machine cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the folding machine cylinder block is about 1-2 days, rolling 1 meter of the folding machine cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the folding machine cylinder increases by 25%. If the folding machine cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality folding machine cylinders, you must take the rolling production process. After the folding machine cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The pressure of the sliding surface of the folding machine cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the folding machine cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about folding machine cylinder:

What is a hydraulic cylinder assembly?
Assembly, which means aggregate. A series of parts or products, formed to achieve a specific function of the whole, the general term for this system is assembly. The hydraulic cylinder assembly is not a single hydraulic cylinder part, which can be used by connecting the hydraulic hose.

Why is there noise in the hydraulic cylinder of the excavator lift arm?
There is no noise of a normal cylinder, check whether the throttle is ringing, or the mechanical part connected with it is ringing, and the mechanical part can be greased. If it can't be ruled out, disconnect the cylinder from the mechanical part and act alone to see what the situation is.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲草鸡巴| 激情无月网址| 男人和美女在搞鸡巴| 色五月中文字幕91精品| 嗯嗯啊啊嗯嗯啊啊视频| 青青五月草视频在线播放| 玩中国美女逼精视频| 操老太太网站| 大鸡吧操美女视频在线播放| 黑人大鸡巴抽插美女| 大鸡巴操逼逼性交网站| 亚卅五月色| 美女一区视频桃花| 国产内射视频99| 操人妻熟妇| 婷婷五月色天亚洲| 97香蕉超碰资源网| 东京热亚州无码AV| 中国女同互扣一区二区三区 | www.色色大香蕉综合网| 亚洲av国产一区二区| 美女操逼软件| 插饥渴美女逼逼| 亚洲一区二区AV电影| 老司机精品99视频观看| 要我,国产视频| 美国操逼免费| 日韩骚货逼| 黄浦区| 欧美最最大胆露阴| 嗯嗯嗯嗯嗯噗嗤噗嗤啊啊啊啊视频在线| 精品成人黄色在线| 美女大鸡巴操逼哦哦啊| 制服中文人妻字幕精品| 欧美日韩中高清伦理成人视频网址 | 国产剧情精品十一区| 超碰黄色大香蕉| 在线观看超清三区av| 亚洲传媒一区| 美女白丝逼逼| 自拍欧美小h视频网站|