亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to Ecuador

Release time:2023-11-19 14:06:45 Hits: Current position: Home > News

This article mainly introduces:

Ecuador hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

Ecuador stroke adjustable cylinder

(Ecuador stroke adjustable cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stroke adjustable cylinder are widely used in Ecuador,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stroke adjustable cylinder for customers from Ecuador.

Introduction to stroke adjustable cylinder:

stroke adjustable cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards stroke adjustable cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the stroke adjustable cylinder guide is determined by the length of the stroke. Check the strength of stroke adjustable cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

When the hydraulic oil is not pumped into the stroke adjustable cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the stroke adjustable cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

We can not just consider the price and ignore the quality when we purchase the stroke adjustable cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the stroke adjustable cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the stroke adjustable cylinder is not required.

When installing the stroke adjustable cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stroke adjustable cylinder block, and the by-pass pipe must be installed in front of the oil port of the stroke adjustable cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stroke adjustable cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stroke adjustable cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stroke adjustable cylinder:

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.

Why does the hydraulic cylinder not return?
For a spring return cylinder, it is possible that 1, the spring is damaged. You can check it for processing. 2, the oil in the oil path is not unloaded, causing it to be unable to reset. 3, the cylinder piston is dead, resulting in no position. For double-acting cylinders, it is possible to: 1, the spool is not reversed, or is not changed to the correct position, check whether the reversing valve is normal (and whether there is electricity). 2, the cylinder piston is dead, resulting in no position, check and treatment can be. 3, the return oil pressure is insufficient, the inlet oil is not unloaded, the operation is not smooth. For reference only.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中国美女操逼逼试頻| 欧美老女人谣乱视频| 国产激情性爰打洞穴| 日韩女优播放一区二区| 操操操操操操操操小骚逼| 台湾佬中文娱乐网222WwW| 啊啊啊啊啊啊鸡巴| 成人A一片| 久久婷婷香蕉热狠狠综合| 日韩性爰视频网站| 美女扒开下面给你捅| 美女屄屄爽| 插逼啊啊啊视频| 专二区女少妇精品99网站| 国国产熟女出轨91嗷嗷叫| 国产一区二区视频91| 国产乱伦丝袜熟女一二三| 欧美熟女丝袜大鸡巴| 一区的视频| 国产在线另类日韩播放| 日韩夫妻性交交换片| 国产白浆操骚逼吃鸡巴高潮| 做暧暧欧美日韩| 看免费的日B片子| 日本大鸡巴精品极品| 哥也要婷婷亚洲| 久久人妻伦一二三区| 尤物人妻一区二区| 大香蕉日B视频| 操到出水视频一区| av北条麻妃在线| 操逼啦啊啊啊视频| 五月婷婷深夜| 欧美福利片视频在线观看| 欧美亚洲另类国产日韩| 好大好长嗯嗯嗯嗯在线观看| 精品人妻无码一区二区三区果冻| 日本老司机在线| 大粗鸡巴r人妻| 18禁福利视频| 天天日老熟女|