亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pipe bender hydraulic cylinder Sold to Saudi Arabia

Release time:2023-11-18 17:15:31 Hits: Current position: Home > News

This article mainly introduces:

Saudi Arabia hydraulic cylinder,pipe bender hydraulic cylinder manufacturer,pipe bender hydraulic cylinder

Saudi Arabia pipe bender hydraulic cylinder

(Saudi Arabia pipe bender hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

pipe bender hydraulic cylinder are widely used in Saudi Arabia,because of no transmission clearance,simple structure and reliable operation,excellent temperature resistance.So our company has designed pipe bender hydraulic cylinder for customers from Saudi Arabia.

Introduction to pipe bender hydraulic cylinder:

The repair method of pipe bender hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

There are some honeycomb holes in the inner wall of the pipe bender hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the pipe bender hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the pipe bender hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the pipe bender hydraulic cylinder is targeted to prevent. Is very necessary.

The "O" ring can be used as an auxiliary seal inside the pipe bender hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the pipe bender hydraulic cylinder, and can be completely sealed.

Repair method of small range wear of oil pipe bender hydraulic cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

Answers to some questions about pipe bender hydraulic cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大香蕉一区二区三区在线观看历史| 乳交日韩在线精品| 91 国产丝袜在线观看| 深爱激情综合在线| 肛交精品在线| 日韩乱性视频网| 在线观看石原莉奈的视频| 日韩人妻老师BB操| 国产日韩欧美中文海角九一| 黑屌后入大屁股| 五十路末亡人四十岁熟女视频| 伊人 激情| 欧美在线中文字幕一区二区三区| 台湾中出三级| 靠逼日逼日骚逼| 动漫操骚逼的视频| 操视频b| 肏亚洲小穴| 欧美和老女人操屄乱视频| 高潮喷水呻吟久久久久久久久| 鸡巴插进逼里免费视频| 营口操逼网| 人妻少妇偷人精品9| av免费在线观看国产一区| 成熟少妇骚穴福利视频| 少妇人妻21P| mitao.av一区| 韩国骚妇艹| 日本人妻丝袜一区二区三区| 日老熟女,国产视频| 5月天1区2区3区婷婷伊人| 国产蜜臀在线播放| 肥熟女精品视频| 日本码一在线| 爱爱激情综合网| 亚洲色欧美色另类在线| 欧美在线观看费视频| 有码视频在线播放网站| 91久久精品美女自慰抽插高潮喷水 | 久久精品涩| 性夜夜久夜夜|