亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

earring type cylinder Sold to The Philippines

Release time:2023-11-08 08:11:58 Hits: Current position: Home > News

This article mainly introduces:

The Philippines hydraulic cylinder,earring type cylinder manufacturer,earring type cylinder

The Philippines earring type cylinder

(The Philippines earring type cylinder,produced by Hengyu Hydraulic Cylinder Factory)

earring type cylinder are widely used in The Philippines,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed earring type cylinder for customers from The Philippines.

Introduction to earring type cylinder:

If the seal of the earring type cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and earring type cylinder, and the phenomenon of "pulling the earring type cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

earring type cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the earring type cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

Factors that should be considered when selecting the oil seal in the earring type cylinder: some specific factors should be taken into account when selecting the oil seal in the earring type cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: earring type cylinder diameter, piston rod diameter, piston rod and piston groove size, earring type cylinder working pressure, earring type cylinder movement speed, hydraulic system oil temperature and earring type cylinder working environment.

When the earring type cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the earring type cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the earring type cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about earring type cylinder:

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
看日本和韩国女人操逼| 国产2025年精品免费看| 操小逼二A| 人妻模特木下凛凛子在线| 大鸡男女生三级黄色欧美| 亚洲操比网| 91大蜜桃臀后入网站| 操B网址直接进入| 精品国自产拍老熟女视| 香蕉色逼| 久久青青青青草| 嗯啊日本片啊啊啊| youjizzmobi怡红院| 人妻丝袜淫乱中文有码熟妇丝袜 | 日韩精品免费性色宅男视频一区二区| 大鸡巴A V| 精品自拍视频网站| 欧美日韩成人影视大全| 人人操色播基地| 黄色片国产黑丝袜区。| 伊人九九久久| 在线观看成人AV一区| 国产的鸡巴又粗又大| 逼逼想要鸡巴日黄视频| 欧美日韩成人Ⅴ| 好吊日殴美| 台湾佬综合娱乐网夜夜草| 男人第一天堂网AV| 动漫一区二区在线李彦宏| 女同脚一区二区| 91精品福利一区二区| 日本亚洲家庭中文区| 亚州另类一区二区| 亚洲操肥逼好视频| 亚洲黄色开心网| www.色色大香蕉综合网| 肏丝袜一区| 视频不卡一区中文字幕| 美女内射视频在线观看| 青青草青娱乐操逼视频| 亚洲福利成人|