亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Cameroon

Release time:2023-11-18 17:15:13 Hits: Current position: Home > News

This article mainly introduces:

Cameroon hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Cameroon single rack cylinder

(Cameroon single rack cylinder,produced by Hengyu Group)

single rack cylinder are widely used in Cameroon,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed single rack cylinder for customers from Cameroon.

Introduction to single rack cylinder:

After the single rack cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

single rack cylinder body inspection: The inner surface of the single rack cylinder and the piston seal are the main factors causing the leakage in the single rack cylinder, if the single rack cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the single rack cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

When the single rack cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

The piston rod of the single rack cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

Answers to some questions about single rack cylinder:

When there is only one hole in the oil inlet and outlet of the hydraulic cylinder, will there be oil leakage?
It is a single acting oil cylinder. This oil cylinder is always driven by hydraulic oil in advance, and is generally pulled back by the spring at the bottom of the piston or the weight of the cylinder piston or the load. But either way, it has nothing to do with any internal leakage. Whether the oil is internally drained is related to the sealing and accuracy of the cylinder itself.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大几把插美女| 超碰2021中文字幕总站| 亚洲考比视频一区二区三区| 中字无码 在线看| 人妻视频欧美| 五月丁香婷婷在线有码中文字幕| 91精品蜜臀| 亚洲看靠逼视频的网站| 性生活高潮αV无码视频| 亚洲鸡巴插入视频| 女同性恋欧美日韩一区二区三区| 欧美人妻少妇被猛烈进入中文字幕| dxj福利| 欧美 日韩 熟女 中文 区 国产| 国产91色综合| 制服丝袜诱惑一区| 深夜精品一区| 进入小穴在线观看| 91久久精品一二三四| 国产精品中文字幕欧美熟女人妻 | 国产精品日本诩吹| 日韩少妇在线观看视频| 91干大神在线视频| 美女一区区| 国产精品内射啪啪| 麻豆天美午夜在线| 人人操人人操人人人操人人操人人| 制服诱惑二区| 亚洲性爱p| 啊小穴被操红了视频| 亚洲一二三区不卡AV在线| 天天综合台湾中文| 嗯嗯啊啊啊啊啊嗯嗯嗯嗯嗯| av鸡巴大| 卡一卡二卡三机械公司| 非洲视频一二三区| 日韩,国产,无码,操逼| 大鸡吧抽插视频无码免费| 亚洲色av熟妇熟女| 看国产美女直播逼| 武鸣县|