亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Chile

Release time:2023-11-18 17:15:10 Hits: Current position: Home > News

This article mainly introduces:

Chile hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Chile swager cylinder

(Chile swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Chile,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed swager cylinder for customers from Chile.

Introduction to swager cylinder:

If the swager cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The piston rod and guide sleeve function of the swager cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

The quality of the swager cylinder can not be ignored in the purchase of the swager cylinder. The swager cylinder is the main component of the swager cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. swager cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of swager cylinder is deep hole processing, which has always troubled the processing personnel.

Before the swager cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

Answers to some questions about swager cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

What is the cylinder with rod cavity, what is the rodless cavity.
The rod cavity is the end of the piston rod, the rodless cavity is the end without the piston rod.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
鸡巴又粗又长又黄成人网站| 深爱五月激动情网在线视频| 色综合麻豆| 无吗人妻一区二区三区在线看| 日b三级视频| 青青操到呻吟在线视频| 二区小视频二区小视频| 东京热中文字幕免费系列| 吞精av网站| 啊啊啊啊啊 国 产 一 区| 狠狠色一级毛片精品一区二区 | 国产熟女网址| 欧美美女操逼操的通红| 国产精品换脸操逼| 亚洲人妻大黑逼在线| 一级黄色大娱片| 香蕉不卡福利| 亚洲制服丝袜诱惑| 嗯啊 嗯嗯操在线观看w| 人妻少妇久久中文字幕久久| 亚州操逼AV| 本道AV高清在线| 台湾妹娱乐222| 亚洲 中出 中文| 91精品推荐| 国产AV免观| 大黑屌VS中国人妻中文字幕| 欧美自拍偷拍导航| 欧美草逼大全套| 日小逼免费视频| 插的好深视频久久| 嗯嗯啊好爽在线观看| AV一不卡二卡| 国产狂肏女主播| 中文字募4区| 国产白嫩被弄高潮91| 用大鸡巴操小骚逼视频| 欧美爱爱插口粗精品| 人妻熟女麻豆| 大鸡巴操逼逼毛免费视频| 台湾中文娱乐网一区二|