亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Spain

Release time:2023-11-17 13:21:59 Hits: Current position: Home > News

This article mainly introduces:

Spain hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Spain shearing machine cylinder

(Spain shearing machine cylinder,produced by Hengyu Group)

shearing machine cylinder are widely used in Spain,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed shearing machine cylinder for customers from Spain.

Introduction to shearing machine cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular shearing machine cylinder action. Troubleshooting method: Replace the rubber hose.

shearing machine cylinder use should try to avoid sealing belt into the shearing machine cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the shearing machine cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the shearing machine cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

shearing machine cylinders in series, parallel and series parallel. Series: In the shearing machine cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the shearing machine cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the shearing machine cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the shearing machine cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

When the hydraulic oil is not pumped into the shearing machine cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the shearing machine cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

Answers to some questions about shearing machine cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

How does the clamping cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, The executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, The control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, The auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕二区在线三区| 成人熟女大屁股一区二区三区| 中文字幕黑鸡巴| 影音先锋熟女少妇资源| 碰超碰免费在线观看| 国产91熟女视频在线| 男人天堂av区| 美女大操逼| 免费看操小逼| 天天操天天射夜夜爽| 日韩制服人妻中文| 老司机精品在线欧美综合| 日韩大香蕉免费| 百虎精品一区| 美国看片网站女生的大鸡巴| 日本精选一区二区| 四房婷婷五月天基地| 一二三区在线精品| 亚洲丝久久| 亚州美女操逼逼| 日韩少妇mf视频在线观看| 俄罗斯美女交配视频| 四虎成人情爱免费视频| 黑人大肌巴操亚洲女Aⅴ在线| 逼久久| 最新中文字幕在线网站一区| 青青草原男人天堂网| 九七超碰人妻| 大基吧操逼视频| 永胜县| 国产传媒电影在线| 亚洲精品秘 一区二区三区蜜臀| 久久大黑逼视频| 日色天天综合| 日韩性片网| 日逼视频,| 尤物视频 91| 大鸡巴操操操| 日韩欧美激情国产精品| 作爱视频91| 成人福利免费在线观看视频|