亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push bench hydraulic cylinder Sold to Burma

Release time:2023-11-17 13:21:52 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,push bench hydraulic cylinder manufacturer,push bench hydraulic cylinder

Burma push bench hydraulic cylinder

(Burma push bench hydraulic cylinder,produced by Hebei Hengyu company)

push bench hydraulic cylinder are widely used in Burma,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed push bench hydraulic cylinder for customers from Burma.

Introduction to push bench hydraulic cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Causes and countermeasures of oil push bench hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the push bench hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the push bench hydraulic cylinder is visibly scarred, the push bench hydraulic cylinder must be replaced. It can be pressurized at one end of the push bench hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most push bench hydraulic cylinder piston drift may not come from the push bench hydraulic cylinder, the above method to determine the push bench hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

When using the push bench hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the push bench hydraulic cylinder block. If the push bench hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the push bench hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the push bench hydraulic cylinder, so that the working efficiency of the push bench hydraulic cylinder is reduced.

When the oil pressure of the push bench hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about push bench hydraulic cylinder:

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美大香蕉在线不卡| 夫妻性生活手机视频在线看| 欧美视频com.V| 免费日韩黄频| 亚洲日韩性爱无码网| 久久黄色小说| 中文字幕乱码精品一区二区三区| 性感美女尿尿逼逼逼逼逼| 美女被操视频下载链接| 91人妻一区二区三区蜜桃麻豆日韩| 男女日逼,男女日逼视频| 人妻丝袜中文字幕av| 一级黄色aD片| 五月天艹骚逼综合| 成年人全裸体一级黄色录像| 色播操逼女人网| 想看黑人女人大逼搞大吊| 日本女优女同性恋强奸| 大鸡巴 抽插 白浆| 日韩欧美骚逼| 老湿机国产精品| 青青草久热国产无码| 中文字幕视频一区无码系列| 国产亚洲蜜臀一区二区三区| 人与动物精品一区二区三区| 五月天色婷婷激情综合深爱| 欧美日韩在线字幕| av一区二区观看| 日韩午夜一区二区精品伦理| 女操吊| 久久久久人妻精品一区| 午夜美女逼逼| 亚洲情六月丁香| 性交中出在线| 中文字幕日本有码一区| 亚洲有码 AV在线| 亚洲看靠逼视频的网站| 嗯嗯啊艹出 嗯啊嗯嗯啊艹视频| 人妻少妇69久久中文字幕| 欧美高消内射厕所尿尿| 大鸡巴进去视频|