亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Uganda

Release time:2023-11-17 13:21:51 Hits: Current position: Home > News

This article mainly introduces:

Uganda hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Uganda trunnion cylinder

(Uganda trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Uganda,because of long service life,smooth movement,high work efficiency.So our company has designed trunnion cylinder for customers from Uganda.

Introduction to trunnion cylinder:

trunnion cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The repair method of trunnion cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When the trunnion cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the trunnion cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about trunnion cylinder:

What is the valve on the hydraulic cylinder?
Oil valve, relief valve, overload valve, explosion-proof valve, etc., these are very convenient to insert! The oil valve, the overload valve and the blasting valve are very important for larger cylinders. Manufacturers will not offer you the selection. You need to choose the values by yourself according to your system, pump, cylinder, environment, working conditions and other comprehensive consideration!

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产二区三区精品福利在线播放| 日韩av中出在线| 欧美操b大片久久网| 又搞又插视频一区二区| 美女黑丝操逼网站| 麻豆╳视频| 桦川县| 91尤物在线看| 熟妇精品欧美| 美女叉开腿让男人捅| 国产视频在线视频嗯嗯啊啊啊| 97色精品亚洲| 操骚逼操操操| 夫妻无码视频一区二区| 最初六十路,七十路AV| ,32操骚免费视频| 一区二区在线观看亚洲在线| 亚洲激情综合天堂| chinese偷拍自| 99爱性网| 国产白虎尤物AV一区二区| 91蜜臀探花在线播放| 射进去操逼视频| 欧美操黑丝| www.骚女熟妇.com| 操你妈骚逼操你妈骚逼操你妈骚逼 | 操B对话国产在线| 9久热国产精品视频| 美女白虎流水被操| 日B免费视频、、| 大香蕉视频一区| 少妇人妻综合久| 老头老太太日逼免费视频| 国产激情з∠视频一区二区| 国外黄片12345| 嗯嗯啊不行啊日本在线| 九色国产性爱导航| 孕妇扣逼毛片视频| 大黑屌插少妇| 自拍18区| 日本人妻初脱人妻搭讪|