亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Sri Lanka

Release time:2023-11-17 13:21:49 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Sri Lanka swager cylinder

(Sri Lanka swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Sri Lanka,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed swager cylinder for customers from Sri Lanka.

Introduction to swager cylinder:

The repair method of swager cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

swager cylinders in series, parallel and series parallel. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the swager cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the swager cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

swager cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the swager cylinder head itself is the guide sleeve of the piston rod, the swager cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the swager cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

The swager cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure swager cylinder can use 20 steel pipe, and the high pressure swager cylinder can use 45 steel pipe.

Answers to some questions about swager cylinder:

How to limit cylinder push rod rotation?
In general, the push-rod rotation can be limited after the push-rod is connected to the pushed mechanism. For example, the push rod is hinged with the push mechanism, or the push mechanism itself is guided, which can limit the rotation of the push rod.

What is a mold core cylinder?
Simple plastic parts can be directly pushed out by the ejector rod after injection molding, complex plastic parts can not be directly pushed out by the ejector rod after injection molding, to make the interference part active, control its position through the cylinder (injection molding into the mold, so that the shape of the plastic parts meet the demand, exit after opening the mold, so that the plastic parts are smoothly pushed out), This kind of cylinder is the mold core cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产 操 办公室少妇 视频| 美女让男生桶18禁| 大鸡巴操美女在线观看| 日韩成人网站欧美| 二区三区五区高清性爱视频| 午夜操逼福利| 日韩欧尤物久久精品一区二区三区| 操死我们视频| 妈妈がだけの心に漂う| 久久一二三四区视频播放| 欧美日本性生活免费看| 熟女啪啪AV| 大鸡巴捅逼av| 伊人网激情视频| 国产女人十分钟免费看| 91成人网三级视屏| 好舒服啊啊啊啊啊啊视频| 精品亚洲偷拍综合| 88av日本| 啊啊啊啊啊啊鸡巴| 国产馆刺激露脸一区| 日美女日爽日出水!| 美女啪啪视频福利| 嗯嗯啊啊,操逼视频| 欧美三级免费黄录像| 大鸡巴操女视频| 91社区视频蜜臀| 欧美日韩亚洲国语| 大鸡吧插小穴视频重口| 几把插入北操视频| 欧美爱爱视频二区| 好好草好好插| 久久精品亞洲麻豆傳媒| 大鸡吧操骚逼网| 美女扒开尿口捅爽免费观看一区二区| 欧美大鸡吧查逼视频| 黑屌视频在线免费视频| 国产五十路人妻在线| 播放黄色熟女少妇| 搞日韩逼| 国产肥熟妇一区二区三区四区五区|