亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Sri Lanka

Release time:2023-11-17 13:21:38 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Sri Lanka steering power cylinder

(Sri Lanka steering power cylinder,produced by Hengyu Group)

steering power cylinder are widely used in Sri Lanka,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed steering power cylinder for customers from Sri Lanka.

Introduction to steering power cylinder:

The coordination of the sliding parts of the steering power cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

When the steering power cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the steering power cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

How to determine the working pressure of the steering power cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, steering power cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Do not regularly check the damage of the chrome layer of the steering power cylinder: completely extend the steering power cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the steering power cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the steering power cylinder seal. Welding slag is strictly prohibited on the surface of the steering power cylinder.

Answers to some questions about steering power cylinder:

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

How to calculate the cylinder diameter, rod diameter and pressure of the cylinder, and how to output tonnage?
Hydraulic cylinder output force F=PAX10^3(KN) F is the output force (KN), P working pressure (MPa), A is the piston or plunger area of action.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
制服丝袜自拍偷怕| 操操操操骚逼| 淫淫AV一·二区| 小香蕉入骚13| 一本色道久久综合亚洲88| 超碰日本公开在线| 大香蕉手机在线免费| 日本伦精品人妻一区二区| 天天艹夜夜| 91|九色|农村老熟女| 亚洲伦理片一区二区在线| 强插人妻三四区| 亚洲大鸡巴插逼| 一区 二区 三区 四区 18b| 亚洲老妇性爱视频在线播放| 日本精品综合色区| 美女扒开尿道让男人捅爽视频| 亚欧洲精品免费观看视频| 久久精品成人一区二区三区97精品 | 国产一级AV又粗又大又| 小个子美女的逼逼好操| www.av.国产传媒.xom| 啊啊啊大奶子爽视频网站| 寂寞人妻少妇一区| 汨罗市| 欧美日韩国产在线,| 亚洲国产精美又黄又爽视频| 福利视频一二三| 色诱色偷偷久久综合| 熟女啪啪AV| 欧美在线一.| 国产高潮白浆AV在线| 亚洲美女人妻在线视频| 中文字幕一区二区无码砖2020 | 日本熟妇视频在线观看免费| 美女黄色片视频| 红桃精品一区| 欧美日韩一区乱| 全球精品福利视频一| 老师久久久久久久久久久| 欧美三区在线视频|