亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

electromagnetic induction cylinder Sold to Czech Republic

Release time:2023-11-08 08:11:55 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,electromagnetic induction cylinder manufacturer,electromagnetic induction cylinder

Czech Republic electromagnetic induction cylinder

(Czech Republic electromagnetic induction cylinder,produced by Hengyu Group)

electromagnetic induction cylinder are widely used in Czech Republic,because of simple structure and reliable operation,powerful torque,clever hydraulic energy conversion.So our company has designed electromagnetic induction cylinder for customers from Czech Republic.

Introduction to electromagnetic induction cylinder:

The cavitation of the electromagnetic induction cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the electromagnetic induction cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The pressure of the sliding surface of the electromagnetic induction cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the electromagnetic induction cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Most of the failure of the electromagnetic induction cylinder is because there is a foreign body in the electromagnetic induction cylinder into the failure of the electromagnetic induction cylinder, the most problematic is that it is difficult to determine when the foreign body is into the electromagnetic induction cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

There are some honeycomb holes in the inner wall of the electromagnetic induction cylinder, piston or piston rod surface. How is this formed? When we repair the electromagnetic induction cylinder, we can see that there are some honeycomb holes on the inner wall of the electromagnetic induction cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the electromagnetic induction cylinder is targeted to prevent. Is very necessary.

Answers to some questions about electromagnetic induction cylinder:

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩亚洲淫乱性爱| 黑丝美女被操出水| 免费看操日本美女视频| 中文字幕在线一区二区| Hc黄片| 葡萄牙性视频一二区| 欧美熟妇视频淫乱视频| 久热久精久品| 日韩欧美激情亚洲激情另类国产| 欧美一区二区美婷| 亚洲色图 欧美色图 激情在线 | 八戒八戒一区二区在线观看| 操大B骚妇视频在线观看-一| 美女被操操的视频| 343级美女日逼| 亚洲一级中出| 啊啊哦好舒服视频| 把美女操一操| 熟女在线一区二区| 无码日韩一区二区红桃| 亚洲色情精品区| 一本道在线大香蕉| 香蕉五月婷婷久久| 中韩黄色| 老肥妇一区二区老熟女| 国产高清色片| 欧美日韩激情小说| 亚洲少妇18op| 青铜峡市| 一本道精品一区| 大鸡巴搞美少妇| 爱爱久久综合| 91男人操白丝美女| 七月婷婷六月色综合| 【大几八操老逼】综合精品| 亚洲成人av一二三| 亚州一区二区Av无码| 国产亚洲精品美女久| 激情文学中文字幕插| np骚逼视频| 日韩精品老司机|