亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

rolling mill cylinder Sold to Holland

Release time:2023-11-16 08:44:43 Hits: Current position: Home > News

This article mainly introduces:

Holland hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

Holland rolling mill cylinder

(Holland rolling mill cylinder,produced by Hengyu Group)

rolling mill cylinder are widely used in Holland,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed rolling mill cylinder for customers from Holland.

Introduction to rolling mill cylinder:

When the rolling mill cylinder is in use, ensure that the rolling mill cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

The piston rod and guide sleeve function of the rolling mill cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

In order to ensure the service life of the rolling mill cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the rolling mill cylinder, causing damage to the seal and causing leakage in the rolling mill cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

rolling mill cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the rolling mill cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about rolling mill cylinder:

How many kinds of cylinder seal repair kit are there?
Very much, a wide variety of imported and domestic, J type, UHS, DHS, O-ring, Sterseal, etc., as well as support bars, materials are different, according to the size of the pressure selection is different, the appearance of the structure is different, the size is a variety, maintenance is generally selected according to the needs of the cylinder.

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美乱伦无码一区| 成人91C.XXX色情网址| 日本韩国免费一级片| 国产后入小视频不卡| 涩3涩3精3品7hqq091b5k| 欧美一区二区美婷| 黑人大鸡巴AA极片| 免AV一片| 大几把艹嫩逼视频| 得得干中文激情在线| 熟妇色一区| av色中字在线| 后入 一区| 蜜臀福利在线| 日韩欧美九区| 日胖屄女人视频| 婷婷香蕉导航| 女生18在线观看网站| 亚洲插插Av| 麻豆91在线视频| 日美女的小骚逼| 亚洲一区丝袜教师| 男鸡巴操女逼视频| 日韩欧美福利久久| 免费日本欧美的非洲| 骚货刺激国产精品视频| 嗯嗯嗯国产片| 波多野结衣又大又紧又爽| av美女在线一区| 夫妻性生活黄色一级片| 超碰免费公| 末女人的逼视频网站| 老女人乱婬一区二区三区| 美女ASHIPIN| 美女的屁眼一区| 熟妇视频88| 久久婷婷美国| 操小骚逼的视频| 91视频婷婷五月天| 国产免费不卡看小穴| 欧美w www|