亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 tons hydraulic press cylinder Sold to Estonia

Release time:2023-11-16 08:44:36 Hits: Current position: Home > News

This article mainly introduces:

Estonia hydraulic cylinder,500 tons hydraulic press cylinder manufacturer,500 tons hydraulic press cylinder

Estonia 500 tons hydraulic press cylinder

(Estonia 500 tons hydraulic press cylinder,produced by Hebei Hengyu company)

500 tons hydraulic press cylinder are widely used in Estonia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed 500 tons hydraulic press cylinder for customers from Estonia.

Introduction to 500 tons hydraulic press cylinder:

The viscosity of the working oil used in the 500 tons hydraulic press cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

When the 500 tons hydraulic press cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the 500 tons hydraulic press cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the 500 tons hydraulic press cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the 500 tons hydraulic press cylinder can meet the requirements by grinding. However, the life and reliability of this repair 500 tons hydraulic press cylinder are not high.

Do not regularly check the damage of the chrome layer of the 500 tons hydraulic press cylinder: completely extend the 500 tons hydraulic press cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the 500 tons hydraulic press cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the 500 tons hydraulic press cylinder seal. Welding slag is strictly prohibited on the surface of the 500 tons hydraulic press cylinder.

When the 500 tons hydraulic press cylinder needs to be stored for a period of time, please follow the recommended methods: The 500 tons hydraulic press cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the 500 tons hydraulic press cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil 500 tons hydraulic press cylinder should not be in direct contact with water vapor for a long time. The 500 tons hydraulic press cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the 500 tons hydraulic press cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the 500 tons hydraulic press cylinder Before working, the 500 tons hydraulic press cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the 500 tons hydraulic press cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about 500 tons hydraulic press cylinder:

How does the one-way solenoid valve control the hydraulic cylinder circuit?
If your cylinder is single-acting, you can use a one-way solenoid valve, such as some lifting platform hydraulic cylinder, the support valve used is one-way (two-position tee), that is, the cylinder extends out by the oil pressure top, the cylinder retracted by its own weight.

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操美女BB视频| 视频国产欧美视频| 国产爱玩屁眼的| 蜜桃大胆人体艺术| 欧美日韩成人版欧美| 日韩伦理在线亚洲一区| 欧美日韩国产卡戴珊视频在线| 成人在线视频你懂的| t偷拍自拍| 黑人大鸡吧干日本女人| 黑人大鸡巴A极片| 男生操美女视频网站| 草草草在线视。| 日本性生活XXX一区二区| www.色色大香蕉综合网| 高清 无码 久久| 国产69精品一区二区三区| 亚洲老年性爱| 日韩性欧美视频| 欧美大鸡吧视频免费在线观看 | 亚洲不卡1234| 白丝美女高潮在线网站| 欧美干逼逼| 欧美白皙一区视频在线观看| 中文字幕国产视频色五月婷婷| 九九亭亭中文字幕| 五月天激情综合网男男| 亚洲有码在线电影| 久久美女精品福利视频| 91蜜臀无码人妻久久探花| 戳B免费视频| 九九淫乱视频| 好骚色一区| 男人操女人下面视频| 欧美午夜福利大奶一区二区| 狠狠插天天干| 激情都市网男人天堂| 捆绑女人一区二区三区| 丝袜美女的鸡巴视频| 国外视频一区二区| 欧美日韩性淫视频观看|