亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

flanged hydraulic cylinder Sold to Holland

Release time:2023-11-16 08:44:20 Hits: Current position: Home > News

This article mainly introduces:

Holland hydraulic cylinder,flanged hydraulic cylinder manufacturer,flanged hydraulic cylinder

Holland flanged hydraulic cylinder

(Holland flanged hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

flanged hydraulic cylinder are widely used in Holland,because of no need for deceleration device,long service life,smooth movement.So our company has designed flanged hydraulic cylinder for customers from Holland.

Introduction to flanged hydraulic cylinder:

The flanged hydraulic cylinder should be vented: when the flanged hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the flanged hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the flanged hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the flanged hydraulic cylinder, the oil is best entered and discharged from the highest point of the flanged hydraulic cylinder. flanged hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When installing the flanged hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the flanged hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the flanged hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the flanged hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the flanged hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

flanged hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The internal leakage of the flanged hydraulic cylinder is an important indicator to measure the quality of the flanged hydraulic cylinder: the internal leakage of the flanged hydraulic cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the flanged hydraulic cylinder, so that the flanged hydraulic cylinder can not accurately and stably stop in a certain position of the flanged hydraulic cylinder, so it is one of the main indicators of the flanged hydraulic cylinder.

Answers to some questions about flanged hydraulic cylinder:

How to refuel pneumatic riveting cylinder?
First put the gun flat, that is, horizontally, while pushing the stroke positioning pin and loosen the back cover, rotate to the left for a maximum of five turns, and then use a wrench to loosen the oil sealing screw, slowly add the hydraulic oil and let the air out, fill up to tighten the oil sealing screw. This process of adding hydraulic oil is over.

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
俄罗斯大鸡吧操日韩| 抽插视频白浆| 20AB中文字幕| 亚不卡一二三四| 少妇九浅一深人妻| 中文字幕超碰亚洲综合| 亚洲熟女精品一:区二区三区| 蜜臀在线播放91久| 五月婷婷色香视频| 超碰av影院| 啊啊啊啊舒服在线观看| 蜜股一区二区| 人妻少妇在线网| 超碰在线免费福利视屏 | 国产一卡二卡在线免费视频| 大鸡八成人精品网| 老司机香蕉精品| 大鸡巴 日韩无码| 亚洲在线1区2| 激情五月综合五月综合网| 日本黄色欧美激情一区二区 | 东京av在线第一页| 亚州色哟哟av在线| 国产91页| 色综合高清无码| 中文字幕一区二区日韩在线观看 | 日逼啊啊啊好大| 中文字幕WWW色| 色片免费无码| 青州市| 成人午夜AV在线免费| 147午夜视频| 91啪啪啪啪| 污污的网站免费看骚逼喷水| 亚洲中文字幕在线第六区| 固定中出视频在线观看| 宅男诱惑狠狠干| 欧美操大B| 天天操小屄视频| 美女自己在家玩逼视频| 国产青青草精品五月天|